Panasonic NR-B32FE2 Скачать руководство пользователя

Страница: 4 / 63

Install and remove glass shelving securely to prevent risk of injury

When moving, raise the adjustable legs

Dragging the refrigerator will damage the floor. For flooring that may become easily damaged put a protective
board in place.

Do not scrape the metal rails

High temperature hazard

Take care of very hot parts

The compressor, pipes etc. can be very hot during operation and directly after stopping. Also, the heater can be
very hot during power supply and immediately after power supply is stopped. Be careful not to burn yourself by
touching very hot parts.

High temperature hazard

Take care of very hot parts after welding

Pipes etc., are very hot after welding. Be careful not to burn yourself by touching very hot parts.

Take care when filling/discharging refrigerant

Liquid refrigerant directly touching the skin may cause frostbite.

Take care of burrs

Be careful not to cut yourself on metal or plastic burrs.

Take care of condenser/evaporator fins

Be careful not to injure yourself on the fin edges.

Содержание NR-B32FE2
































































Результаты поиска

Содержание NR-B32FE2

Отзывы:

Похожие инструкции для NR-B32FE2

Бренды по названию

Популярные бренды

Panasonic NR-B32FE2, Руководство по обслуживанию

Результаты поиска

Содержание NR-B32FE2

Отзывы:

Похожие инструкции для NR-B32FE2

Бренды по названию

Популярные бренды