Panasonic NR-B32FE2 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 63

background image

44

11.8.5. Install Door A'ssy PC

1. Remove the connector that connect with Door A'ssy PC

a. Remove the screw that is fixation of Cover Cap Door

PCT L.

b. Insert screwdriver (-) into a gap of Cover Cap Door

PCT L, and pry off hooks (2 portions).
Remove Cover Cap Door PCT L.

c. Insert screwdriver (-) into a gap of Cover Harness

PCT L, and pry off hooks (3 portions).
Remove Cover Harness PCT L.

d. Pull out the connector that is connected with Door

A'ssy PC, and remove the connector while pressing
toward upper side.

e. Store the connector in Cover Harness PCT, install

Cover Harness PCT in Door A’ssy PC as before.

2. Install Door A'ssy PC

a. Apply the grease on around Pin Hinge Center.
b. Lift Door A’ssy PC, and insert left bottom of Door A’ssy

PC into Hinge Center L.

3. Install Hinge Top L

a. Through the connector to the hole of Hinge Top L.

CAUTION

• Be careful not to forcibly bend when the connector is

through the hole of Hinge Top L. Because it might be
cause to wire cut and connector damage.

b. Apply the grease on the tongue of Hinge Top L and

insert it into Door A’ssy PC.

c. Three screws that are fixation of Hinge Top L are tem-

porarily screwed.

«
...
42
43
44
45
46
...
»

Содержание NR-B32FE2
































































Отзывы:

Нет отзывов

Похожие инструкции для NR-B32FE2

Бренд: EAS Electric Страницы: 107

Бренд: EAS Electric Страницы: 120

Бренд: Fhiaba Страницы: 27

Бренд: Igloo Страницы: 15

Бренд: U-Line Страницы: 47

Бренд: Yale Страницы: 14

Бренд: Gram Страницы: 84

Бренд: Baumatic Страницы: 14

Бренд: Vestfrost Страницы: 124

Diplomat DAR0488BL

Бренд: Danby Страницы: 13

Бренд: NEFF Страницы: 28

Бренд: Gram Страницы: 84

Бренд: Salora Страницы: 35

Бренд: ARDESTO Страницы: 60

Бренд: Indesit Страницы: 12

Бренд: Gram Страницы: 132

Monogram ZIF360NHXH

Бренд: GE Страницы: 20

Monogram ZIC360NRGLH

Бренд: GE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды