Panasonic NR-B30FG1 Скачать руководство пользователя страница 47

Страница: 47 / 67

11.8.5. Install Door A'ssy PC

1. 1. Remove the connector that connect with Door

A'ssy PC

a. Remove the screw that is fixation of Cover Cap

Door PCT L.

b. Insert screwdriver (-) into a gap of Cover Cap Door

PCT L, and pry off hooks (2 portions).
Remove Cover Cap Door PCT L.

c. Insert screwdriver (-) into a gap of Cover Harness

PCT, and pry off hooks (2 portions).
Remove Cover Harness PCT.

d. Pull out the connector that is connected with Door

A'ssy PC, and remove the connector while press-
ing toward upper side.

e. Store the connector in Cover Harness PCT, install

Cover Harness PCT in Door A’ssy PC as before.

2. Install Door A'ssy PC

a. Apply the grease on around Pin Hinge Center

b. Lift Door A’ssy PC, and insert left bottom of Door

A’ssy PC into Hinge Center L.

3. Install Hinge Top L

a. Through the connector to the hole of Hinge Top L.

CAUTION

• Be careful not to forcibly bend when the connec-

tor is through the hole of Hinge Top L. Because it
might be cause to wire cut and connector dam-
age.

b. Apply the grease on the tongue of Hinge Top L

and insert it into Door A’ssy PC.

c. Three screws that are fixation of Hinge Top L are

temporarily screwed.

d. Adjust Door A’ssy PC perpendicularly and hori-

zontally in the same of Door A’ssy FC.

Содержание NR-B30FG1




































































Результаты поиска

Содержание NR-B30FG1

Отзывы:

Похожие инструкции для NR-B30FG1

Бренды по названию

Популярные бренды

Panasonic NR-B30FG1, Руководство по обслуживанию

Результаты поиска

Содержание NR-B30FG1

Отзывы:

Похожие инструкции для NR-B30FG1

Бренды по названию

Популярные бренды