background image

PART

QUANTITY

Wood Screws

2

(

1

4

“ x 2“)

Toggle Bolts (and
wing nuts) (

3

16

“ x 3“)

Self-Aligning Machine

Screws (

1

4

“-28 x 3

1

4

“)

Nylon Grommet
(for metal cabinets)

1

If the unit is damaged in shipment,

return the

unit to the store in which it was bought for repair
or replacement. 

If the unit is damaged by the customer,

repair or 

replacement is the responsibility of the customer. 

If the unit is damaged by the installer

(if other

than the customer), repair or replacement must
be made by arrangement between customer 
and installer. 

DAMAGE—SHIPMENT/
INSTALLATION

Installation Instructions

PARTS INCLUDED

You will find the installation hardware contained in
a packet with the unit. Check to make sure you have
all these parts.

NOTE:

Some extra parts are included.

HARDWARE PACKET

PART

QUANTITY

Template 

1

Template

Installation

 1

Instructions

Separately

 

2

Packed

 

Filters

 

PARTS INCLUDED 

(CONT.)

INSTALLA

TION

INSTRUCTIONS

ADDITIONAL PARTS

1

adaptor

Grease

 

Exhaust

Glass

          

1

Tray

1

Ring

T r

u ntable 

Cabinet

Top

Rear Wall

2

1

Use & Care 

1

Shelf 

1

1

USE & CARE 

MANUAL

Manual

For some models 

Convection

wire rack

For some models 

For some models 

1

PureAir@

Microwave

Filter

EN-4

Содержание NN-SG158S



























Отзывы: