background image

 

3

 

  PRECAUTIONS FOR SAFE OPERATION

 

 

It is imperative that the user complies with this operating instructions 
as it contains important safety advice.

 

 

Items and procedures are described so that you can use this unit correctly and safely.   
If the precautions advised are followed, this will prevent possible injury to the user and 
any other person. 
 
Precautions are illustrated in the following way: 

 

WARNING

 

Failure to observe WARNING signs could result in a hazard to personnel 
possibly resulting in serious injury or death.

 

 
 

CAUTION

 

Failure to observe CAUTION signs could result in injury to personnel and 
damage to the unit and associated property.

 

 

Symbol shows;

 

 
       

 

 

this symbol means caution.

 

 
       

 

 

this symbol means an action is prohibited.

 

 
       

 

 

this symbol means an instruction must be followed.

 

 

Be sure to keep this operating instructions in a place accessible to users of this unit.

 

 
 

< Label on the unit > 

This mark is labeled on the cover in which the electrical components of high voltage 
are enclosed to prevent the electric shock. 
The cover should be removed by a qualified engineer or a service personnel only. 

 
 

WARNING

 

As with any equipment that uses CO

2

 gas, there is a likelihood of oxygen depletion in the 

vicinity of the equipment.  It is important that you assess the work site to ensure there is 
suitable and sufficient ventilation.    If restricted ventilation is suspected, then other methods of 
ensuring a safe environment must be considered.    These may include atmosphere monitoring 
and warning devices. 

 
 
 

 

Содержание MDF-C8V1 Series










































Отзывы: