-6-
PARTS LIST
(NOZZLE HOUSING)… BLOCK
A
Ref. No.
Part Name & Description
Part No.
Quantity
Remarks
A – 1
Nozzle Housing
ACØ1ACBYZYU2
1
A – 2
Window
AC21HAGZZYØ2
1
A – 3
Shaft, Plastic
AMC25S-VØØ
1
A – 4
Furniture Guard
AC1ØAAGZZVØ7
1
A – 5
Light Cover
AC24HAPPZYU2
1
A – 6
Bracket, Handle Release
AC43AAFY2ØØ
1
A – 7
Spring, Pedal
AC58AAFVZØØ
1
A – 8
Shaft, Pedal
AMC51A-V3Ø
1
A – 9
Pedal, Handle Release
AMC47A-2VØU
1
A – 10
Screw, Frame
AXTN4 +14BFY
3
Shipped 10 per package
A – 11
Screw, Light Cover
AXTN4 +16BFY
2
Shipped 10 per package
A – 12
Belt
AC28SJPZØØ
1
A – 13
Nozzle Pipe
AC7ØSZA1ØØ
1
A – 14
Lower Plate Assembly
AC91ABAYZVØ6
1
A – 15
Lower Plate
AC27AAFWZVØ6
1
Includes A-16 Packing & A-30 Screws
A – 16
Packing, Lower Plate
AC19AARKZVØØ
1
A – 17
Belt Guard
AC43SAFVZØØ
1
A – 18
Slider Support
AC53KAPNZWØ3
1
A – 19
Screw, Slider Support
AXTN4 +16BFY
2
Shipped 10 per package
A – 20
Screw, Nozzle
AMC68A-V3Ø
2
Shipped 10 per package
A – 21
Stop Latch Spring
AC7ØNYUZØØ
2
A – 22
Height Adjustment Cam
AC61KJPZVØ6
1
A – 23
Screw, Slider Support
AC68AZAZØØ
1
Shipped 10 per package
A – 24
Sliding Knob
AC57HJPZVØ6
1
A – 25
Wheel
AC9ØQNGZVØ6
2
A – 26
Shaft, Wheel
AC16CNXZØØ
2
A – 27
Latch
AMC68N-AVØK
2
A – 28
Screw, Body Lower Plate
AXTN4 +16BFY
2
Shipped 10 per package
A – 29
Body, Lower Plate
ACØ6AAJUZØØ
1
A – 30
Screw, Metal Lower Plate
AXTS3+10BFY
4
Shipped 10 per package
-19-
CARBON BRUSH REPLACEMENT
Removal and Installation
1.
After removing the motor, see MOTOR REPLACEMENT, make
sure that you have properly identified it. Note specifically that this
motor is made in the U.S.A. as identified by the label on the side of
the motor, or Made in U.S.A. stamped on the bottom.
2.
Remove the amp terminals located on each brush end,
(Fig. 16)
.
Replace the brush assembly which should include the brush holder.
Reinstall the amp terminals onto the new brush assembly. Complete
brush change on one side before starting on the other side.
NOTE: Do not drop screws into the motor.
3.
There are two (2) brushes located on the motor as identified in
(
Fig. 16)
. A Phillips head screwdriver will be required to remove the
four (4) screws that hold the brush holders onto the motor. See
(Fig. 16)
for screw location.
NOTE: When inserting the brush assembly, be sure that
the TAB on the bottom of the brush holder is positioned in the
trough as shown in Fig. 18.
4.
Replace the brush holder bracket with two (2) Phillips screws on
each side of the motor.
5.
As a final check to assure proper installation of brushes,
measure across the brushes for the approximate dimension as
shown in (
Fig. 17)
.
Made in U.S.A.
Carbon Brushes
Amp
Terminal
Label
Green Ground Wire
(Some Models)
Brush
Screws
Trough
Brush Holder
Tab Location
115-120 mm
4.5 - 4.7"
Brush to Brush
Dimension is Approximate
(Fig. 17)
(Fig. 16)
Removal
1.
Remove the dust cover.
2.
Remove the lower plate, agitator assembly, belt, the plastic shaft, slider support,
light bulb assembly and the nozzle housing as instructed in the respective removal
sections. Remove the plastic holder,
(Fig. 15)
.
3.
Turn the vacuum over to the front side.
NOTE: The bumper is positioned over the top of the motor case. Pull up on
the portion of the bumper that lies across the top part of the motor case to
free the motor case for removal.
4.
Remove the four (4) screws from the motor case and then remove the motor
case,
(Fig. 15)
.
5.
Disconnect the motor leads and remove the motor. Remove the motor support rubber, (rear), noise suppressor, and
the motor support rubber, (front). Place these items on the new motor. See the
C Block
for a view of these.
Installation
1.
Place the motor back into the dust compartment with brushes aligned parallel to the front edge of the dust
compartment. The motor support, (rear) must also align with the tabs in the same direction.
2.
Rewire per the
Pictorial Wiring Diagram
.
3.
Replace the motor case and the four (4) screws.
4.
Replace the bumper by inserting it into the groove in the dust container.
5.
Turn the vacuum back over and replace the plastic holder, thick side out, plastic shaft, slider support, light bulb
assembly, nozzle housing, belt, agitator assembly, and lower plate according to the respective installation instructions.
MOTOR REPLACEMENT
(Fig. 15)
