- 7 -
This vacuum cleaner has a thermal cut-out which
automatically trips to protect the vacuum cleaner from
overheating. If a clog prevents the normal flow of air to the
motor, the thermal cut-out turns the motor off automatically to
allow the motor to cool in order to prevent possible damage to
the vacuum cleaner.
To correct problem: If this occurs, turn the vacuum cleaner
off and unplug the vacuum cleaner from the mains outlet to
allow the vacuum cleaner to cool and the thermal cut-out to
reset. Check for and remove clogs, if necessary. Also
check and clean/replace any clogged filters. Wait
approximately forty (40) minutes before switching on the
vacuum cleaner. The motor protector will not reset if the
vacuum cleaner is not disconnected from the mains
socket even if the vacuum cleaner has cooled down.
H) MOTOR PROTECTOR
Motor Protector
This vacuum cleaner has a motor protector by-pass valve
which automatically opens to provide cooling air to the
motor when a clog prevents the normal flow of air to the
motor. If the by-pass valve opens to prevent motor
overheating and possible damage to the vacuum cleaner,
you will notice a change of sound as air rushes through the
valve opening.
To correct problem: See the TROUBLE-SHOOTING
guide.
NOTE: The motor protector may open when using
attachments or when cleaning new carpet, due to reduced
airflow by the attachments themselves or by new carpet
fluff filling the dust bin quickly. See the TROUBLE-
SHOOTING guide.
I ) THERMAL CUT-OUT
CAUTION:
Do not block motor protector.
G) HOW TO USE THE ACCESSORIES
CAUTION:While using
the accessories, hold the
handle with one hand to
avoid pulling the vacuum
cleaner over.
Lift out accessories needed.
NOTE: After using the accessories, re-insert the hose to the connector pipe.
To avoid accidental injury,
keep children away from the
agitator while in operation.
Connect any of the accessories, as indicated.
1
1
1
2
1
5
1
3
1
4
- 14 -
H) BLOCKAGES
A
B
B
A
Hose Coupling
Suction Inlet
Hose Inlet
Secondary
Filter Screen
The hose located on the vacuum cleaner carries the dirt
from the nozzle up to the dust bin. If the hose should
become clogged:
Unplug the vacuum cleaner from mains outlet.
Remove hose coupling and check hose coupling and hose
inlet for clogs according to the following procedure.
To remove hose coupling:
1.Depress and tilt tab A as shown.
2.Once tab A is clear of the vacuum cleaner inlet, depress
and tilt tab B as shown.
To re-install hose coupling: Reverse steps above.
Check suction inlet and secondary filter screen for clogs.
Disconnect nozzle hose from connector pipe, check the
hose. Plug in vacuum cleaner and turn on.
Stretch hose in and out to remove clog. If clogs still exist,
turn the vacuum cleaner over and inspect agitator area for
clogs, see BELT CHANGING AND CLEANING for details.
Connector Pipe
Nozzle
Hose
1
1
1
2
1
5
Connect Mini turbine nozzle as indicated.
To prevent damage to carpeted
floors when using tools the Carpet /
Bare Floor switch should be place
in ‘O’ to turn the agitator OFF.
I ) HOW TO REMOVE THE TELESCOPIC HANDLE
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
aaaaaaaaaaaaaa
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
bbbbbbbbbbbbbb
With the handle on its lowest position, depress the handle
height adjustment button and raise handle about 6 cm
while turning it counterclockwise.
You should be able to turn the handle 90° to a transversal
position.
Pull handle straight out until free from vacuum cleaner. Do
not use excessive force.
Handle height
adjust button
1
1
1
2
