24
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS FOR THE USER
Before using the vacuum cleaner, please observe these basic precautions.
WARNING: To reduce the risk of fire, electric shock, or injury
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not use the appliance if the mains lead or plug is damaged or faulty.
• If the mains lead is damaged, it must be replaced by the manufacturer, its service agent or similarly quali
fi
ed persons in order to
avoid a hazard.
• Unplug from the socket outlet when not in use and before cleaning the appliance or undertaking maintenance operations.
• Turn off the appliance before removing the plug. Do not pull on the mains lead, always pull on the plug body itself.
• Hold the plug, when rewinding the mains lead.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not use wet
fi
lters after wash, make sure they are completely dry to avoid damaging the cleaner.
• Do not vacuum
fl
ammable or combustible substances, neither use in areas where they may be present.
• Do not vacuum hot ash, embers or large and sharp objects.
• Do not vacuum water or other liquids.
• Keep the vacuum cleaner away from heat sources such as radiators,
fi
res, direct sunlight, etc.
• This vacuum cleaner is
fi
tted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the
motor. When this happens, disconnect the cleaner from the socket outlet and check the dust compartment and
fi
lters as they may
be full or clogged with
fi
ne dust. Check for any other obstructions in the hose or tube. After removing the obstruction, leave the
cleaner to cool down until the thermal cut-out resets after approximately 60 minutes.
C - HOW TO OPERATE YOUR CLEANER
C-1
Pull out the mains lead and put the plug into the socket
outlet.
C-2
Gently press the center of the switch pedal to turn ON
the appliance.
Press the pedal again to turn it OFF.
C-3
Power control
To increase or decrease the power, turn the variable
power control button.
C-4
Switching between carpet and
fl
ooring
Flooring: Press lever
A
Carpet: Press lever
B
C-5
The curved wand off the hose is attached with a manual
suction regulator, which allows you to reduce the suction
level easily.
C-6
After you
fi
nish vacuuming, remove the plug from the
socket outlet and press the cord rewind pedal.
When rewinding the mains lead, press the cord rewind
pedal by holding the plug so that it does not become
damaged.
C-7
Storage position
Slide the wand holder straight into the wand supporter
on the under side of the main body.
C-8
Park position
For short breaks during vacuuming, slide the wand
holder straight into the wand supporter on the rear side
of the main body.
NOTE:
When you use park position, we suggest that
you switch the appliance off.
A- IDENTIFICATION OF MAIN PARTS
A)
Floor nozzle
B)
Connection pipe
C)
Hose
D)
Suction regulator
E)
Curved wand
F)
Telescopic wand
G)
Hose inlet
H)
Dust indicator
I )
Dust cover
J)
ON/OFF Switch pedal
K)
Cord rewind pedal
L)
Crevice nozzle
M)
Dusting brush
N)
Upholstery nozzle
O)
Exhaust cover
P)
Plug
Q)
Variable power control button
R)
Paper dust bag
B - HOW TO ASSEMBLE YOUR CLEANER
B-1
Insert the connection pipe into the hose inlet until it
locks.
When removing the hose, push the two connection
buttons down while pulling out the connection pipe.
NOTE:
Do not bend, pull and step on the hose or put
anything heavy on it.
B-2
Insert the curved wand into the upper end of the
telescopic wand, and the
fl
oor nozzle to the other end.
B-3
Hold the grip and the extension adjuster and extend the
telescopic wand to the required length.
