Panasonic KX-TG6671C Скачать руководство пользователя

Страница: 42 / 52

Error messages

Display message

Cause/solution

Access # to VM service
is not stored

You have not stored the Voice Mail access number. Store the
number (page 37).

Base no power

No link. Re-connect
base AC adaptor.

The handset has lost communication with the base unit. Move
closer to the base unit and try again.

Unplug the base unit’s AC adaptor to reset the unit. Reconnect
the adaptor and try again.

The handset’s registration may have been cancelled. Re-register
the handset (page 27).

Busy

The called unit is in use.

Other units are in use and the system is busy. Try again later.

The handset you are using is too far from the base unit. Move
closer and try again.

Check tel line

The supplied telephone line cord has not been connected yet or
not connected properly. Check the connections (page 8).

Error!!

Recording was too short. Try again.

Invalid

There is no handset registered to the base unit matching the
handset number you entered.

The handset is not registered to the base unit. Register the
handset (page 27).

Requires subscription
to Caller ID.

You must subscribe to a Call Display service. Once you receive
caller information after subscribing to a Call Display service, this
message will not be displayed.

Use rechargeable
battery.

A wrong type of battery such as Alkaline or Manganese was
inserted. Use only the rechargeable Ni-MH batteries noted on
page 4,5.

Useful Information

Содержание KX-TG6671C





















































Результаты поиска

Содержание KX-TG6671C

Отзывы:

Похожие инструкции для KX-TG6671C

Бренды по названию

Популярные бренды

Panasonic KX-TG6671C, Руководство по эксплуатации

Результаты поиска

Содержание KX-TG6671C

Отзывы:

Похожие инструкции для KX-TG6671C

Бренды по названию

Популярные бренды