background image

KX-TG6411FXS/KX-TG6411FXT/KX-TG6412FXS/KX-TG6412FXT/KX-TGA641FXJ/KX-TGA641FXS/KX-TGA641FXT

3

TABLE OF CONTENTS

PAGE

PAGE

1 Safety Precautions

-----------------------------------------------

4

1.1. For Service Technicians --------------------------------- 4

2 Warning

--------------------------------------------------------------

4

2.1. Battery Caution--------------------------------------------- 4
2.2. About Lead Free Solder (Pbf: Pb free)--------------- 4
2.3. Discarding of P.C. Board--------------------------------- 5

3 Specifications

-----------------------------------------------------

6

4 Technical Descriptions

-----------------------------------------

7

4.1. Block Diagram (Base Unit) ------------------------------ 7
4.2. Circuit Operation (Base Unit) --------------------------- 8
4.3. Block Diagram (Handset)-------------------------------11
4.4. Circuit Operation (Handset)----------------------------12
4.5. Circuit Operation (Charger Unit) ----------------------13
4.6. Signal Route -----------------------------------------------14

5 Location of Controls and Components

------------------

15

5.1. Controls -----------------------------------------------------15

6 Installation Instructions

---------------------------------------

16

6.1. Connections------------------------------------------------16
6.2. Battery-------------------------------------------------------16

7 Operating Instructions

-----------------------------------------

18

7.1. Programmable Settings ---------------------------------18
7.2. Registering a Handset to a Base Unit---------------20
7.3. Copying Phonebook Entries ---------------------------20
7.4. Dialling mode ----------------------------------------------21
7.5. Error Messages -------------------------------------------21
7.6. Troubleshooting-------------------------------------------22
7.7. For Service Hint-------------------------------------------26

8 Service Mode

-----------------------------------------------------

27

8.1. Engineering Mode ----------------------------------------27
8.2. Copying Phonebook Items when Repairing -------31
8.3. How to Clear User Setting------------------------------33

9 Troubleshooting Guide

----------------------------------------

34

9.1. Troubleshooting Flowchart -----------------------------34
9.2. Troubleshooting by Symptom (Base Unit and

Charger Unit) ----------------------------------------------46

9.3. Troubleshooting by Symptom (Handset) -----------50

10 Disassembly and Assembly Instructions

---------------

54

10.1. Disassembly Instructions -------------------------------54
10.2. How to Replace the Handset LCD -------------------57

11 Measurements and Adjustments

---------------------------

58

11.1. Equipment Required -------------------------------------58
11.2. The Setting Method of JIG (Base Unit) -------------58
11.3. Adjustment Standard (Base Unit)---------------------60
11.4. Adjustment Standard (Charger Unit)-----------------61
11.5. The Setting Method of JIG (Handset) ---------------62
11.6. Adjustment Standard (Handset) ----------------------64
11.7. Things to Do after Replacing IC or X'tal ------------65
11.8. RF Specification-------------------------------------------67
11.9. How to Check the Handset Speaker or

Receiver ----------------------------------------------------68

11.10. Frequency Table (MHz) ---------------------------------68

12 Miscellaneous

----------------------------------------------------

69

12.1. CPU Data (Base Unit) -----------------------------------69
12.2. CPU Data (Handset)-------------------------------------71
12.3. How to Replace the Flat Package IC----------------73
12.4. How to Replace the LLP (Leadless Leadframe

Package) IC------------------------------------------------75

12.5. Terminal Guide of the ICs, Transistors and

Diodes ------------------------------------------------------ 77

13 Schematic Diagram

--------------------------------------------

79

13.1. For Schematic Diagram -------------------------------- 79
13.2. Schematic Diagram (Base Unit)---------------------- 80
13.3. Schematic Diagram (Handset)------------------------ 82
13.4. Schematic Diagram (Charger Unit)------------------ 84

14 Printed Circuit Board

------------------------------------------

85

14.1. Circuit Board (Base Unit_Main) ---------------------- 85
14.2. Circuit Board (Handset) -------------------------------- 87
14.3. Circuit Board (Charger Unit)--------------------------- 89

15 Exploded View and Replacement Parts List

-----------

90

15.1. Cabinet and Electrical Parts (Base Unit) ----------- 90
15.2. Cabinet and Electrical Parts (Handset)------------- 91
15.3. Cabinet and Electrical Parts (Charger Unit) ------- 92
15.4. Accessories and Packing Materials ----------------- 93
15.5. Replacement Part List ---------------------------------- 96

Содержание KX-TG6411FXS






































































































Отзывы: