Panasonic KX-TG6411FXS Скачать руководство пользователя | Manualshive

Страница: 50 / 101

background image

50

KX-TG6411FXS/KX-TG6411FXT/KX-TG6412FXS/KX-TG6412FXT/KX-TGA641FXJ/KX-TGA641FXS/KX-TGA641FXT

9.3.

Troubleshooting by Symptom (Handset)

If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester
(*1) or not.

Note:

(*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic
level in detail.
(*2) Refer to

Check Point (Handset)

(P.50)

9.3.1.

Check Point (Handset)

Please follow the items below when BBIC or EEPROM is replaced.

Note:

After the measuring, suck up the solder of TP.
*:

Connections

(P.62) is required beforehand.

The connections of adjustment equipments are as shown in

Adjustment Standard (Handset)

(P.64).

Items

Check

Point

Procedure

Check or

Replace Parts

(

A

)* 1.8 V Supply Adjustment

VDD1

1. Confirm that the voltage between test point VDD1 and GND is 1.8 V ± 0.02 V.
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of VDD1 executing command “VDD XX“(XX is the

value).

IC1, Q2, C48,

D1, C1, C44,

R12, R45,

C40, C45, F1

(

B

)*

BBIC Confirmation

-

1. BBIC Confirmation (Execute the command “getchk”).
2. Confirm the returned checksum value.

Connection of checksum value and program number is shown below.

IC1, X1, RA61,

R64, R66

(

C

)* EEP-ROM Confirmation

-

1. EEP-ROM Confirmation (Execute the command "sendchar EPV").
2. Confirm the returned Value (Value for reference is written at "EEPROM C/

SUM" in Software_Version_Table.xls).

IC1, IC3,

R40~R42,

C172

(

D

) Charge Control Check &

Charge Current Monitor

Check

-

1. Apply 3.5 V between CHG(+) and CHG(-) with DC power supply and set cur-

rent limit to 250 mA.
Confirm the indication of “charging” on LCD.

2. Confirm that the current limit LED of DC power supply is ON/OFF.

Confirm it after waiting over 1 minute at least.

3. Decrease current limit of DC power supply to 100 mA.
4. Confirm that the current limit LED of DC power supply is stable. (Current limiter

is ON.)

(If charge control cannot be confirmed by this procedure, please use battery to hand-
set power supply and try again.)

IC1, Q4 Q9,

D7, R6, R7,

F1, C1, R2,

R30, R31, R8,

R45

(

E

)* Charge Detection (OFF)

Check

-

1. Stop supplying 3.5 V to CHG (+) and CHG (-).
2. Confirm the indication of “charging” has been cleared.

IC1, Q4 Q9,

D7, R6, R7,

F1, C1, R2,

R30, R31, R8,

R45

«
...
48
49
50
51
52
...
»

Содержание KX-TG6411FXS






































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TG6411FXS

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 56

Бренд: Uniden Страницы: 51

Бренд: AT&T Страницы: 7

Бренд: Grandstream Networks Страницы: 6

Бренд: Swisscom Страницы: 25

Gigaset CX100 isdn

Бренд: Gigaset Страницы: 123

Бренд: Main Resource Страницы: 16

Бренд: urmet domus Страницы: 52

Бренд: Topcom Страницы: 296

Бренд: BRONDI Страницы: 80

Бренд: Aastra Страницы: 16

Бренд: Alcatel Страницы: 74

Бренд: Uniden Страницы: 76

Бренд: Panasonic Страницы: 248

Бренд: Panasonic Страницы: 10

Easa-Phone KX-T1000

Бренд: Panasonic Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды