Panasonic KX-TCD735ALM Скачать руководство пользователя страница 88

Страница: 88 / 114

Answering System Operations with the Base Unit

To playback new recorded
message(s)

Press .

•

The unit announces the number of new
message and plays them back.

•

During playback, the display shows the
message number.

To playback all recorded
message(s)

Press and hold

firmly until a short

beep sounds.

•

During playback, the display shows the
message number.

•

To increase the volume, press

To decrease the volume, press

•

To increase the volume, press

To decrease the volume, press

4   M e s s a g e s
0   N e w   C a l l s
M e s s a g e   3

Ex.

The unit is playing message 3.

4   M e s s a g e s
0   N e w   C a l l s
M e s s a g e   1

Ex.

The unit is playing message 1.

During Playback of a Recorded Message

To repeat a message

Press .

•

If you press within 5 seconds from start
playback, the previous message will be
played.

•

If you press over 5 seconds from start
playback, the current message will be played.

To skip a message

Press .

•

The next message will be played if recorded.

To stop a message

Press .

•

To resume playback a recorded message,

press

. To return to the standby mode,

press again.

To playback the most recent
message

Press .

KX-TCD735ALM(E)-4(76~100) 2002.06.21 5:30 PM Page 88

Содержание KX-TCD735ALM



















































































































Результаты поиска

Содержание KX-TCD735ALM

Отзывы:

Похожие инструкции для KX-TCD735ALM

Бренды по названию

Популярные бренды

Panasonic KX-TCD735ALM, Руководство по эксплуатации

Результаты поиска

Содержание KX-TCD735ALM

Отзывы:

Похожие инструкции для KX-TCD735ALM

Бренды по названию

Популярные бренды