Panasonic KX-TCA130FXS Скачать руководство пользователя страница 53

Страница: 53 / 115

Items

Check

Point

Procedure

Check or

Replace Parts

(H)* DTMF Generator Check

Connect CN1 (Telephone Socket) to DTMF tester.

Execute the command "hookoff" and "dtmf_hi".

Confirm that the high frequency (1477Hz) is -8 ± 2dBm.

Execute the command "dtmf_lo".

Confirm that the low frequency (852Hz) is -10.5 ± 2dBm.

IC8, R39, C41,

R49, C46, C47,
R42, R43, R44,
R45, R46, R47,

R48, C108,
C109, C40,

C36, Q8, D4

(I)*

Transmitted Power

Confirmation

Remove the Antenna before starting step from 1 to 7.
1.

Configure the DECT tester (CMD60) as follows;

Test mode: FP

Traffic Carrier: 5

Traffic Slot: 4

Mode: Loopback

PMID: 00000

RF LEVEL = -70dBm.

Execute the command "testmode".

Execute the command “sendchar dmv 2 2“.

Check that “Signalling Status” has been set to “Locked“, then press “ACCEPT
RFPI“.

Initiate connection from Dect tester (“set up connect“)

Execute the command “ant0“.

Confirm that the NTP value at ANT is 20dBm ~ 25dBm.

IC2, IC8, R124,

R125, C153,
C140, C141,

DA1, C142,

C143, C144, L3,
L4, R118, R119,

C135, R115,

R116, Q6,

C145, C147,
C149, C151,
C157, R123,
C158, C159,
C160, C161,
C162, C163,
C164, C136,
R117, R127,
C156, C154,

C155

(J)

Modulation Check and

Adjustment

Follow steps 1 to 6 of (I) above.

7.Confirm that the B-Field Modulation is -350 ~ -400/+320 ~ +370kHz/div
using data type Fig31.

8.Adjust the B-Field Modulation if required. (Execute the command "readmod"
and "wrtmod xx", where xx is the value.)

IC2, IC8, R124,

R125, C153,
C140, C141,

DA1, C142,

C143, C144, L3,
L4, R118, R119,

C135, R115,

R116, Q6,

C145, C147,
C149, C151,
C157, R123,
C158, C159,
C160, C161,
C162, C163,
C164, C136,
R117, R127,
C156, C154,

C155

(K) Frequency Offset Check

Follow steps 1 to 6 of (I) above.

7.Confirm that the frequency offset is < ± 45kHz.

IC2, IC8, R124,

R125, C153,
C140, C141,

DA1, C142,

C143, C144, L3,
L4, R118, R119,

C135, R115,

R116, Q6,

C145, C147,
C149, C151,
C157, R123,
C158, C159,
C160, C161,
C162, C163,
C164, C136,
R117, R127,
C156, C154,

C155

KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT

Содержание KX-TCA130FXS




















































































































Результаты поиска

Содержание KX-TCA130FXS

Отзывы:

Похожие инструкции для KX-TCA130FXS

Бренды по названию

Популярные бренды

Panasonic KX-TCA130FXS, Руководство по обслуживанию

Результаты поиска

Содержание KX-TCA130FXS

Отзывы:

Похожие инструкции для KX-TCA130FXS

Бренды по названию

Популярные бренды