Panasonic KX-TCA130FXS Скачать руководство пользователя страница 17

Страница: 17 / 115

6.5. PIN Code

6.5.1. Base Unit

For security, the base unit PIN must be entered when changing certain settings. The default PIN is “

”.

For Service Hint:

*: If the current 4-digit Base Unit PIN is forgotten, follow the procedures below.

1. If Base Unit and Handset are not linked with, first, follow the steps in Registering a Handset to a Base Unit (P.30).

2. Follow the steps above in Base Unit (P.17) of PIN Code. At step 3, enter

, and you will able to enter new

Base Unit PIN.

6.5.2. Handset

For security, the handset PIN must be entered when changing certain settings. The default PIN is “

”.

For Service Hint:

*: If the current 4-digit PIN is forgotten, press

and you will be able to enter new Handset PIN.

This password is useful whether Base Unit and Handset are linked with or not.

KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT

Содержание KX-TCA130FXS




















































































































Результаты поиска

Содержание KX-TCA130FXS

Отзывы:

Похожие инструкции для KX-TCA130FXS

Бренды по названию

Популярные бренды

Panasonic KX-TCA130FXS, Руководство по обслуживанию

Результаты поиска

Содержание KX-TCA130FXS

Отзывы:

Похожие инструкции для KX-TCA130FXS

Бренды по названию

Популярные бренды