Panasonic KX-TCA130FXS Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 115

background image

9 SMS (Short Message Service)

SMS allows you to send and receive text messages between other fixed-line and mobile phones that support compatible SMS
networks and features.

Important:

·

To use SMS features, you must:

−

−

−

−

subscribe to the Caller ID and/or appropriate service

−

−

−

−

confirm SMS is turned on

−

−

−

−

confirm the correct message centre numbers are stored

Consult your service provider for details and availability.

Note:

·

A total of 47 messages (at 160 characters/message) can be saved. Total number may be more than 47 if length of
messages are less than 160 characters/message.

·

If the unit is connected to a PBX system, you may not be able to use SMS features.

9.1. Writing and Sending a New Message

Note:

·

This unit supports SMS messages of up to 612 characters, however, the maximum number of characters you can send or
receive may be limited by your SMS service provider. Consult your SMS service provider for details.

·

If your message contains over 160 characters, the message is a long message and

is displayed. Your service provider

may treat long messages differently from other messages. Consult your service provider for details.

·

“

” is displayed if you try to send a message to a phone number saved in the phonebook, caller list, or

redial list that is over 20 digits long.

·

When sending a message, “

” is displayed momentarily, then “

” is displayed.

·

If your phone is connected to a PBX, store the PBX line access number.

32

KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT

«
...
30
31
32
33
34
...
»

Содержание KX-TCA130FXS




















































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-TCA130FXS

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 396

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 10

DESKTOP DIRECTOR 2101

Бренд: Telos Страницы: 46

Бренд: golmar Страницы: 2

Бренд: Grandstream Networks Страницы: 6

Бренд: Swisscom Страницы: 25

Бренд: Jacob Jensen Страницы: 16

DECT 1730 Series

Бренд: Uniden Страницы: 32

T42S-Skype for Business

Бренд: Yealink Страницы: 8

Бренд: AT&T Страницы: 35

Бренд: Alcatel Страницы: 46

Бренд: TACKLIFE Страницы: 10

Бренд: Grandstream Networks Страницы: 40

Бренд: Furuno Страницы: 2

Бренд: SwiftCam Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды