Panasonic KX-PRW130C Скачать руководство пользователя страница 47

Страница: 47 / 60

Note:

You can also use the

soft key, if

displayed, to play new Voice Mail
messages.

If the handset still indicates there are new
messages even after you have listened to
all new messages, turn it off by pressing
and holding

until the handset beeps.

Error messages

Display message

Cause/solution

Ask phone
company for
VM access #

You have not stored the Voice Mail access number. Store the
number (page 46).

Base no power

No link to base.
Reconnect main
base AC adaptor.

The handset has lost communication with the base unit. Move
closer to the base unit and try again.

Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.

The handset’s registration may have been cancelled.
Re-register the handset (page 32).

Busy

The called unit is in use.

Other units are in use and the system is busy. Try again later.

The handset you are using is too far from the base unit. Move
closer and try again.

Check tel line

The supplied telephone line cord has not been connected yet
or not connected properly. Check the connections (page 8).

Error!!

Recording was too short. Try again.

Invalid

There is no handset registered to the base unit matching the
handset number you entered.

The handset is not registered to the base unit. Register the
handset (page 32).

Memory full

The phonebook memory is full. Erase unwanted entries
(page 18).

Message memory is full. Erase unwanted messages
(page 38).

The call block list memory is full. Erase unwanted entries
(page 29).

The schedule alarm memory is full. Erase unwanted entries
(page 31).

Handset memory is full. Erase unwanted wallpaper images,
photos, or ringtones (page 24).

Requires
subscription
to Caller ID.

You must subscribe to a Call Display service. Once you
receive caller information after subscribing to a Call Display
service, this message will not be displayed.

Use
rechargeable
battery.

A wrong type of battery such as Alkaline or Manganese was
inserted. Use only the rechargeable Ni-MH batteries noted on
page 3, 6.

Useful Information

PRW130C(en)_0311_ver110.pdf 47

2014/03/11 13:06:45

Содержание KX-PRW130C





























































Результаты поиска

Содержание KX-PRW130C

Отзывы:

Panasonic KX-PRW130C, Руководство по эксплуатации, Страница: 47 / 60

Результаты поиска

Содержание KX-PRW130C

Отзывы: