Panasonic KX-MB2085CXW Скачать руководство пользователя страница 265 | Manualshive

Страница: 265 / 276

background image

4

Adjust the recording paper guides. Pinch the front
side of the recording paper guide (

D

), then slide it to

match the paper size mark. Pinch the right side of the
recording paper guide (

E

), then slide it to adjust the

width to the size of the recording paper.

R

Make sure that the recording paper is under the
paper limit mark (

F

), and the paper should not

be loaded over the snubbers (

G

).

G

D

E

F

5

Insert the paper input tray into the unit, lifting the front
part of the tray. Then push it completely into the unit.

Note:

R

If the paper is not loaded correctly, re-adjust the
paper guides, or the paper may jam.

R

If the paper input tray does not close, the plate in the
paper input tray may not be in the locked position.
Push the paper down and make sure that the paper
is laying flat in the paper input tray.

Caution for the paper input tray

R

Do not drop the paper input tray.

R

Hold the paper input tray with both hands when
removing or installing. The paper input tray
weighs approximately 2 kg when fully loaded with
recording paper.

Approx. 2 kg

1.7.1 Manual input tray

You can use the manual input tray for printing with the
computer and for copying. When printing or copying
multiple sheets, add the next sheet after the first sheet
has been fed into the unit.

R

Please refer to page 110 for information on recording
paper.

R

When printing from a computer, custom size
recording paper can also be used (page 28).

R

The unit is set for printing A4-size plain paper by
default.

–

To use other paper sizes, change the
recording paper size setting (feature #381 on
page 58).

–

To use other paper types, change the
recording paper type setting (feature #384 on
page 58).

1

Adjust the width of the guides (

A

) to the size of the

recording paper.

R

If the unit is in sleep mode, press a key to standby
the unit for the next process.

15

1. Introduction and Installation

«
...
263
264
265
266
267
...
»

Содержание KX-MB2085CXW





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-MB2085CXW

Magicolor 2 Desklaser

Бренд: QMS Страницы: 60

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: Panasonic Страницы: 166

Бренд: Oki Страницы: 104

Бренд: Lexmark Страницы: 500

Бренд: Rena Страницы: 59

Бренд: Xerox Страницы: 214

Бренд: Cardco Страницы: 28

Бренд: Gainscha Страницы: 12

Бренд: DataCard Страницы: 8

KX-P1131 - KX-P 1131 B/W Dot-matrix Printer

Бренд: Panasonic Страницы: 6

KX-MC6000 Series

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 24

KX-P1131 - KX-P 1131 B/W Dot-matrix Printer

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 43

Бренд: Panasonic Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды