Panasonic KX-MB2085CXW Скачать руководство пользователя страница 127

Страница: 127 / 276

127

KX-MB2085CXW/KX-MB2090CXW

12.3.11.4. How To Output The Journal Report

1. Press the MENU button 3 times.
2. Press “#”, then “2”.
3. Press the SET button.
4. The report prints out.

CROSS REFERENCE:

Features

(P.13)

Error code table:

SND=TRANSMISSION / RCV=RECEPTION

Most fax communication problems can be resolved by the following steps.

1. Change the transmit level. (Service code: 596, refer to

Service Function Table

(P.75).)

2. Change the TX speed/RX speed. (Service code: 717/718, refer to

Service Function Table

(P.75).)

Note*:

If the problem remains, see the following “

Countermeasure

” flow chart.

(1) CODE

(2) RESULT

(3) MODE

SYMPTOM

Counter-

measure*

PRESSED THE STOP KEY

SND & RCV Communication was interrupted by the STOP button.

DOCUMENT JAMMED

SND

The document paper is jammed.

NO DOCUMENT

SND

No document paper.

THE COVER WAS OPENED SND

The cover is open.

COMMUNICATION ERROR

SND

Invalid signal is received during PHASE-B of PHASE-D.

COMMUNICATION ERROR

SND

Transmission is finished when the T0 TIMER expires.

COMMUNICATION ERROR

SND

DCN is received after DCS transmission.

COMMUNICATION ERROR

SND

FTT is received after transmission of a 2400BSP training signal.

COMMUNICATION ERROR

SND

No response after post message is transmitted three times.

COMMUNICATION ERROR

SND

RTN and PIN are received.

COMMUNICATION ERROR

RCV

No response after FTT is transmitted.

COMMUNICATION ERROR

RCV

No post message.

COMMUNICATION ERROR

RCV

RTN is transmitted.

COMMUNICATION ERROR

RCV

PIN is transmitted (to PRI-Q).

COMMUNICATION ERROR

RCV

PIN is transmitted.

COMMUNICATION ERROR

RCV

Reception is finished when the T0 TIMER expires.

ERROR-NOT YOUR UNIT

RCV

DCN is received after DIS transmission.

COMMUNICATION ERROR

RCV

DCN is received after FTT transmission.

ERROR-NOT YOUR UNIT

SND

DCN responds to the post message.

COMMUNICATION ERROR

SND

DCN is received before DIS reception.

COMMUNICATION ERROR

RCV

Reception is not EOP, EOM PIP, PIN, RTP or RTN.

COMMUNICATION ERROR

RCV

No response at the other party after MCF or CFR is transmitted.

ERROR-NOT YOUR UNIT

RCV

DCN is received after CFR transmission.

COMMUNICATION ERROR

RCV

Carrier is cut when the image signal is received.

MEMORY FULL

RCV

The document was not received due to memory full.

CANCELED

SND

The multi-station transmission was rejected by the user.

COMMUNICATION ERROR

SND & RCV Modem error. For the DCN, DCN, etc. abbreviations, refer to

NCU

Section

(P.29).

ITS (Integrated telephone System) and Monitor

Section

(P.31).

Содержание KX-MB2085CXW





















































































































































































































































































Результаты поиска

Содержание KX-MB2085CXW

Отзывы:

Похожие инструкции для KX-MB2085CXW

Бренды по названию

Популярные бренды

Panasonic KX-MB2085CXW, Руководство по обслуживанию

Результаты поиска

Содержание KX-MB2085CXW

Отзывы:

Похожие инструкции для KX-MB2085CXW

Бренды по названию

Популярные бренды