Panasonic KX-MB1530E Скачать руководство пользователя страница 68

Страница: 68 / 92

10.2 Display messages

To indicate the unit’s status, one or more of the following messages will appear on the display.

Display

Cause & Solution

“

CALL SERVICE

”

There is something wrong with the unit. Contact our service personnel.

“

CHANGE CARTRIDGE

”

The toner cartridge is not inserted properly. Re-insert it correctly (page 10).

There is something wrong with the toner cartridge. Replace the toner
cartridge.

“

CHECK CARTRIDGE

”

The toner cartridge is not inserted properly. Re-insert it correctly (page 10).

“

CHECK DOCUMENT

”

The document was not fed into the unit properly. Remove the document,
and then press

Stop

to clear the message. Re-insert the document. If

misfeeding occurs frequently, clean the document feeder rollers
(page 83) and try again.

The ADF top cover is not fully closed. Push firmly on the front and rear edges
of the ADF top cover, and then feed the document again.

“

CHECK PAPER #1

”

Recording paper is not installed or the paper input tray has run out of paper.
Install paper (page 13).

Recording paper was not fed into the unit properly. Re-insert the recording
paper (page 79).

The paper input tray is not installed or is not inserted completely. Insert the
paper input tray into the unit.

“

CHECK PAPER TRAY #1

”

The loaded recording paper is not the appropriate size. Load recording
paper of the size that is shown on the display.

If this message is often displayed, also change the recording paper size
setting (feature #380 on page 54).

The recording paper size setting (feature #380 on page 54) is set to

“

16K

”

, so received faxes will have been stored into memory. Change the

recording paper size setting and load the appropriate recording paper.

Note:

“

”

: Check the paper input tray. The displayed paper size depends on the

recording paper size setting (feature #380 on page 54).

“

”

: Check the manual input tray. The displayed paper size depends on

the recording paper size setting (feature #381 on page 54).

“

CHECK PICK UP INPUT

TRAY #2

”

Recording paper was not fed into the unit properly. Load the paper again
(page 79).

“

COOL DOWN FUSER

”

The unit is cooling down the fuser unit. Wait for a while.

“

DRUM LIFE LOW REPLACE

SOON

”

The drum inside the toner cartridge is reaching the end of its life. If you
don’t have a new cartridge handy you should buy one as soon as possible
as your current cartridge is near the end of its useful life.

“

DRUM LIFE OVER CHANGE

CARTRIDGE

”

The drum inside the toner cartridge has reached the end of its useful life.
Replace the toner cartridge immediately.

Note:

As a temporary measure, you can press

Start

to continue printing.

However, the printing quality may be poor, so we do not recommend
continuous use of a cartridge once it has exceeded its useful life.

“

FAX IN MEMORY

”

The unit has a document in memory. See the other displayed message
instructions to print out the document. For fax memory capacity, see
page 85.

If the PC fax setting (feature #442 on page 60) is set to

“

ALWAYS

”

– check the connection between the computer and the unit.
– check that the computer is turned ON.

“

FRONT COVER OPEN

”

The front cover is open. Close it.

10. Help

Содержание KX-MB1530E





























































































Результаты поиска

Содержание KX-MB1530E

Отзывы:

Похожие инструкции для KX-MB1530E

Бренды по названию

Популярные бренды

Panasonic KX-MB1530E, Руководство по эксплуатации

Результаты поиска

Содержание KX-MB1530E

Отзывы:

Похожие инструкции для KX-MB1530E

Бренды по названию

Популярные бренды