Panasonic KX-FM330GR Скачать руководство пользователя страница 63

Страница: 63 / 264

(6) Insert the three green gears into the remaining cores

of the new film.

(7) Insert the film into the cartridge so that the blue gear

matches the blue label on the cartridge.

(8) Lock the four gears of the film by ( A ) pushing back

the top side gears and ( B ) pulling the bottom side
gears forwards until they click into place.

•

If the film is slack, tighten it by winding the bottom

side gears.

(9) Insert the film cartridge by matching the blue label on

the cartridge with that on the unit.

(10) Close the front cover securely by pushing down on both

ends.

•

The unit will check the film is set correctly and the follow-

ing message will be displayed.

•

If the following message is displayed, the film is not

correctly inserted in the cartridge.

Reinsert it correctly.

Slots

Guide tabs

Green gears

Top side
gears

Bottom
side gear

Bottom
side gears

Blue label

Blue gear

Film

Cartridge

Film
cartridge

Blue labels

Incorrect

Correct

Display:

(Bitte warte)

PLEASE WAIT

(Film prüfen)

CHECK FILM

•How much film you have left

To check the amount of remaining film, press FILM REMAINING while the unit is idle. The display indicates the approximate

amount of remaining film.

Display:

When the film indicator points to this position, the remaining film will print up to 25

pages of letter size documents. Prepare a new film or film cartridge for replacement.

FILM E F

(FILMANZEIGE)

(Film – +)

Note:

Words in brackets ( ) are German. A translated version for each market is available with this model series.

KX-FP320G / KX-FM330G

Содержание KX-FM330GR









































































































































































































































































Результаты поиска

Содержание KX-FM330GR

Отзывы:

Похожие инструкции для KX-FM330GR

Бренды по названию

Популярные бренды

Panasonic KX-FM330GR, Руководство по обслуживанию

Результаты поиска

Содержание KX-FM330GR

Отзывы:

Похожие инструкции для KX-FM330GR

Бренды по названию

Популярные бренды