Panasonic KX-FM330GR Скачать руководство пользователя страница 62

Страница: 62 / 264

1.14.9. REPLACING THE FILM CARTRIDGE

FILM EMPTY

(Film erschšpft)

(1) Slide the front cover open lever forwards to open

the front cover.

(2) Remove the film cartridge.

•

If you have purchased a film cartridge (Parts no.

KX-FA135X) for replacement, skip to step 9.

•

To replace only the film(Parts no. KX-FA136X), go

to step 3.

(3) Unlock the four gears by ( A ) pulling the top side

gears (blue and green gears) forwards and ( B )
pushing back the bottom side gears (green gears)
and remove the used film.

(4) Remove the four gears from the used film cores.

Caution:

•

The film is not reusable. You can order a new film

for replacement through your nearest Panasonic
dealer. (Refer to page 9)

(5) Insert the blue gear into the blue core of the new

film.

When the unit detects the end of the film, the following message will be displayed.

The remaining film produces approx. 10 A4 size documents. Prepare a new film
or film cartridge.

The film is empty. Replace the film or film cartridge with a new one.

For film and film cartridge information, refer to page 9.

Cover open
lever

Film cartridge

Blue gear

Green gear

Green
gear

Bottom side gears

Top side gears

Film cores

Gears

Slots

Blue gear

Guide tabs

Blue core

FILM NEAR EMPTY

(NŠhe Filmende)

Note:

•

Words in brackets ( ) are German. A translated version for each market is available with model series.

KX-FP320G / KX-FM330G

Содержание KX-FM330GR









































































































































































































































































Результаты поиска

Содержание KX-FM330GR

Отзывы:

Похожие инструкции для KX-FM330GR

Бренды по названию

Популярные бренды

Panasonic KX-FM330GR, Руководство по обслуживанию

Результаты поиска

Содержание KX-FM330GR

Отзывы:

Похожие инструкции для KX-FM330GR

Бренды по названию

Популярные бренды