Panasonic KX-FM330GR Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 264

background image

Bit No.

DIS/DTC

DCS

43

R16×15.4 lines/mm and/or 400×400 pels/25.4 mm

R16×15.4 lines/mm and/or 400×400 pels/25.4 mm

44

Inch based resolution preferred

Resolution type selection
"0" : neritic based resolution
"1" : inch based resolution

45

Metric based resolution preferred

DonÕt care

46

Minimum scan line time capability for higher resolutions
"0" : T

15.4

= T

7.7

"1" : T

15.4

= 1/2T

7.7

DonÕt care

47

Selective Polling capability

Set to "0".

48

Extend field

Extend field

Note 1 - Standard facsimile units conforming to T.2 must have the following capability : Index of cooperation (IOC)=264.

Note 2 - Standard facsimile units conforming to T.3 must have the following capability : Index of cooperation (IOC)=264.

Note 1 - Standard facsimile units conforming to T.4 must have the following capability : Paper length=297 mm.

Signal

Identification Signal Format

Function

Training 1

———————

A fixed pattern is transmitted to the receiving side at a speed
(2400 to 9600 bps) designated by DCS, and the receiving side
optimizes the automatic equalizer, etc., according to this signal.

TCF
(Training Check)

———————

Sends 0 continuously for 1.5 seconds at the same speed as the
training signal.

CFR
(Confirmation to Receive)

X0100001

Notifies the sending side that TCF has been properly received. If
TCF is not properly received, FTT (Failure To Train) X0100010 is
relayed to the sender. The sender then reduces the transmission
speed by one stage and initiates training once again.

Training 2

———————

Used for reconfirming the receiving side like training 1.

Image Signal

Refer to the next page.

———————

RTC
(Return to Control)

———————

Sends 12 bits (0...01 × 6 times) to the receiver at the same speed
as the image signal and notifies completion of transmission of the
first sheet.

EOP
(End of Procedure)

X1110100

End of one communication

MCF
(Message Confirmation)

X0110001

End of 1 page reception

DCN
(Disconnect)

X1011111

Phase E starts.

MPS
(Multi-Page Signal)

X1110010

Completion of transmission of 1 page. If there are still more
documents to be sent, they are output instead of EOP. After MCF
reception, the sender transmits an image signal of the second
sheet.

PRI-EOP
(Procedural Interrupt-EOP)

X1111100

If there is an operator call from the sender, it is output after RTC.

PIP
(Procedural Interrupt Positive)

X0110101

This is output when an operator call is received.

166

KX-FP320G / KX-FM330G

«
...
206
207
208
209
210
...
»

Содержание KX-FM330GR









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FM330GR

Бренд: Makita Страницы: 5

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 6

Бренд: NanaWall Страницы: 22

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 75

Бренд: Janome Страницы: 40

Бренд: Janome Страницы: 45

Бренд: Janome Страницы: 51

Бренд: Janome Страницы: 2

MEMORY CRAFT 9700

Бренд: Janome Страницы: 110

Memory Craft 3000

Бренд: Janome Страницы: 42

Memory Craft 10001

Бренд: Janome Страницы: 181

Бренд: Janome Страницы: 41

Бренд: Janome Страницы: 32

Бренд: ZOJE Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды