Panasonic HIT VBHN320KA03 Скачать руководство пользователя

Страница: 11 / 14

Using a lay-in lug with bolt and

nut

(see Figure 6.3)



If using this method, please follow

instructions in previous section re-

garding using bolts and nuts with

larger grounding holes.



Use a grounding tin plated solid

copper lay-in lug rated for direct

burial and outdoor use. Lug must be

used ILSCO GBL-4DBT,

BurndyCL501TN.



Attach grounding lug to module

frame using a stainless steel bolt

and lock-nut.



Tighten stainless steel set screw at

the torque specified by lug manu-

facturer to secure copper wire.



The specified torque is following



Ilsco Corp. GBL-4DBT

10-14AWG-Solid -> 20 in-lbs,

4-6AWG-Strand -> 35 in-lbs,

8AWG-Strand -> 25 in-lbs, 10-

14AWG-Strand -> 20 in-lbs



Burndy L L C CL501TN 14AWG-

Solid -> 35 in-lbs,

14AWG-Strand -> 35 in-lbs, 4AWG

-Strand -> 45 in-lbs



Recommended torque value in

tightening bolt and nut is 2.3 N.m

(20in-lb).

Note: Use the ground holes

illustrated in Figure 6.1.

Select a grounding the fol-

lowing lug.

ILSCO GBL-4DBT,

Burndy CL501TN

Figure 6.3

Using a lay-in lug with bolt and nut

Содержание HIT VBHN320KA03















Результаты поиска

Содержание HIT VBHN320KA03

Отзывы:

Похожие инструкции для HIT VBHN320KA03

Бренды по названию

Популярные бренды

Panasonic HIT VBHN320KA03, Основное руководство по установке

Результаты поиска

Содержание HIT VBHN320KA03

Отзывы:

Похожие инструкции для HIT VBHN320KA03

Бренды по названию

Популярные бренды