15
English
16
English
AFTER COMPLETING THE MASSAGE
RETURN THE SEAT TO THE ORIGINAL POSITION
1
Check that there is nothing in the vicinity of
the backrest.
2
Press the OFF/ON button twice.
The backrest will automatically return to its original position.
3
Place the controller in its holder.
4
Return the pillow and the back cushion to
their original positions.
•
DISCONNECT THE POWER
See Warning No. 1 on page 1.
1
Slide the power switch to the “off” position.
2
Turn the lock switch key to the “lock” position.
3
Unplug the power cord.
4
The lock switch key must be stored out of the reach of children.
CLEANING AND MAINTENANCE
See Danger No. on page 1.
LEATHER COVERING ON THE PILLOW, THE BACK CUSHION AND THE UNIT
Wipe these areas with a soft, dry cloth.
(Do NOT use cloths containing any kind of chemical, etc.)
If the leather is particularly dirty, dampen with liquid soap and brush the surface. Wipe with a cloth dampened with water. Allow
to dry naturally.
(Do NOT use a hair dryer to try to dry the surfaces more quickly.)
Wearing of denim, colored, patterned or other clothing with a tendency to fade should be avoided during use, as it could lead to
discoloration of the leather.
Please do NOT use thinners, benzine or alcohol.
PIPE AND PLASTIC AREAS
1 Wipe the unit with a cloth that has been soaked in a mild detergent and then thoroughly wring out.
Next wipe the unit with a cloth that has been moistened with just water and thoroughly wring out.
*Make sure you thoroughly wring out the cloth first when cleaning the controller.
3 Allow the unit to dry naturally.
Please do NOT use thinners, benzine or alcohol.
COATED FABRIC
1 Wipe the seat fabric with a cloth that has been soaked in a mild detergent solution and then thoroughly wrIng out.
Use a brush to apply a mild detergent to areas where the coated fabric has become particularly soiled. Be careful not to brush
the fabric too much as this may damage it.
3 Next wipe the fabric with a cloth that has been moistened with just water and then thoroughly wrIng out.
4 Allow the fabric to dry naturally.
Please do NOT use thinners, benzine or alcohol.
•
•
•
•
•
•
TROUBLESHOOTING
Problem
Cause and Remedy
Motor Noises
It sounds and feels like the massage heads are straining to get over wrinkles in the cloth.
The motor groans when it comes under load.
There is excessive noise during Tapping. (The noise is greater at the top of the unit.)
There is a creaking noise when the massage heads are in operation.
There is a rattling sound when the massage heads move up or down.
The belt can be heard rotating.
There is a rubbing sound produced by the massage heads rubbing on the seat fabric.
There is a noise when the backrest cushion moves over the armrest when the seat is reclining.
There is a noise when I sit down.
There is a strange sound when the massage heads move in and out.
When the power switch is turned on there is a humming sound.
•
•
•
•
•
•
•
•
•
•
•
These sounds are perfectly normal and will not have any effect on the operation of the unit.
The massage heads stop during operation.
When excessive force is applied to the massage heads during operation, in the interests of safety the massage heads may
stop moving.
If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for
approximately 10 seconds and then turn the power switch on again. If the massage heads stop again, position yourself so
that your back is not completely in contact with the backrest.
The massage heads do not come up to the shoulder or neck.
The position of the massage heads is incorrect.
(See Page 10)
The height of the left and right massage heads is different.
An alternating tapping method is employed, which means that this phenomenon will naturally occur.
There is nothing wrong with the unit.
It is not possible to recline the unit.
If the unit encounters an obstacle or if excessive force is exerted on it during operation, in the interests of safety the unit will
come to a stop.
If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for
approximately 10 seconds and then turn the power switch on again.
Reclining does not take place even though a massage is started in pre-programs.
(The seat does not automatically recline.)
In some cases the seat may not automatically recline depending on the position (angle) of the backrest
(See Page 9)
The backrest does not return to the upright position.
The backrest will not return to the upright position if the timer is activated or the
button is pressed.
(Pressing
twice will return the backrest to its original position.)
(See Page 15)
It is not possible to switch from Swedish and Knead to Hawaiian and Compression.
Switching can be hindered when the user’s body weight is not resting on the massage heads. Shift your weight so that your
body is contact with the massage heads.
The unit will not operate at all.
The power cord has been disconnected.
(See Page 10)
The power switch on the unit has not been turned on.
(See Page 10)
A Pre-Program button or Manual Operation button hasn’t been pressed after pressing
.
(See Pages 9, 1)
•
•
•
The unit has been damaged.
Stop using the unit immediately.
The power cord or power plug is abnormally hot.
Stop using the unit immediately.
See Warning No. 9 and 10 on page .
If service is needed please contact your local dealer or all 1-877 Panafix (73-349).
15-16
2007/12/12 19:14:45
