9
English
10
English
6 ATTACHING THE BACK CUSHION AND PILLOW
1
Attach the back cushion using the zipper.
2
Attach the pillow using the velcroes.
BEFORE USING THE UNIT
1 CHECK THE SURROUNDING AREA
Check that there is nothing around the
unit.
5 FIX THE CONTROLLER CORD
Approx. 0
(51 cm)
Use the controller cord velcroes to secure the cord, leaving approximately 20 in.
(51 cm) of free wire.
* Confirm that there is a margin for the controller cord length when the backrest is reclined.
(The illustration shows that the cord is attached to the right armrest.)
FOLDING THE BACKREST FORWARD (REPACKING)
CAUTION
Keep hands, feet, children, objects, etc., clear of openings on the unit, including seat and armrests; gaps between
the unit and the floor; and the backrest’s range of movement when being folded forward.
Failure to do so could result in injury.
The unit should not be turned on and the controls should not be operated on when the backrest is folded forward.
Failure to follow these instructions could result in injury.
The unit should not be climbed on and objects should not be placed on the unit when the backrest is folded
forward.
Failure to follow these instructions could result in damage to the unit.
In the interests of safety, the backrest should always be folded forward by two persons.
•
•
•
•
1
Press the OFF/ON button to switch off the power.
2
Slide the power switch to the “off” position, lock it, and then unplug the power
cord.
3
Remove the back cushion and the pillow from the unit.
4
Remove the armrest from the unit.
Refer to “INSTALL THE ARMRESTS ON THE UNIT” on page 6 and remove them in
reverse order.
5
Insert a screwdriver into the opening for the backrest latch
approx. 1.6 in. (4 cm) from the upper edge of the opening
(until the screwdriver contacts the backrest latch).
6
Push tip of screwdriver downward approx. 1 in. (2.5 cm) to
release backrest latch.
7
Pull out screwdriver when pushing of backrest toward
seat begins.
*Be careful to avoid catching the controller or the cord between the backrest and the seat.
* It is recommended that you move the unit before folding the backrest (upright
position). When the backrest is folded, it is not fixed and is unstable.
7
7
5
5
6
6
2 POWERING UP THE UNIT
See Warning No. 7 on page 1.
1
Make sure the power plug is functional.
Make sure the power plug is undamaged. Make sure the power plug is free of foreign matter and debris.
2
Plug the power plug into an electrical outlet.
3
Verify that the lock switch key is turned to the “open” position.
If in “lock” position, turn the lock switch key to “open”.
4
Slide the power switch to the “on” position.
3 CHECK THE UNIT
1
3
1
Make sure the chair covering is free of rips or
tears.
2
Make sure there are no obstacles between
the parts of the unit.
3
Make sure the massage heads are in the
retracted position, i.e. they are parked to the
left and right in the upper part of the backrest.
If not retracted, press
twice to return the massage heads to the
retracted position.
See Warning No. 14 on page .
4 ADJUSTING FOR CORRECT PILLOW HEIGHT
Velcroes
Adjust the pillow height so that the bottom edge
of the pillow is at ear level.
If positioned too low, the pillow can lessen the effect of massage around the
neck area.
•
5 ADJUSTING THE RECLINING ANGLE
Press reclining to adjust the angle of the backrest.
With the button held down, movement will continue until a “beep-beep-beep” sound indicates the backrest has been raised or
lowered as far as possible.
Approx. 120˚
Approx. 170˚
* The reclining operation is a function that adjusts the angle of the backrest. Avoid using it for any other purposes, such as
continuous up/down operation etc.
•
•
•
9-10
2007/12/12 19:14:43
