manualshive.com logo in svg

Panasonic EB-GD75, Руководство по обслуживанию

Поделиться
Скачать
Panasonic EB-GD75 Скачать руководство пользователя страница 1

Issue B
Revision 0

© 2001 Matsushita Communication Industrial UK Ltd.
All rights reserved. Unauthorized copying and
distribution is a violation of law.

Order Number: MCUK011201C8

Personal Cellular Phone

EB-GD75

EB-GD75C

Battery life figures are dependent on battery and network conditions, SIM card and usage.

900 MHz

1800 MHz

Frequency Range

Tx: 880 - 915MHz

Tx: 1710 -1785 MHz

Rx: 925 - 960 MHz

Rx: 1805 -1880 MHz

Tx/Rx frequency 
separation

45 MHz

95 MHz

RF Channel Bandwidth

200 kHz

Number of RF channels

174

374

Speech coding

Full rate/Half rate/Enhanced Full rate

Operating temperature

-10 °C to +55 °C

Type

Class 4 Handheld

Class 1 Handheld

RF Output Power

2 W maximum 

1 W maximum

Modulation

GMSK (BT = 0.3)

Connection

8 ch / TDMA

Voice digitizing

13 kbps RPE-LTP / 13 kps ACLEP / 5.6 kps CELP / VSLEP

Transmission speed

270.833 kbps

Diversity

Frequency hopping

Signal Reception

Direct conversion

Antenna Impedance

50

τ

(External Connector)

Antenna VSWR

< 2.1 : 1

Dimensions

Height: 106 mm 

(excluding antenna)

Width:  46 mm

Depth: 16 mm

Volume

77 cc

Weight

82 g

Display

Graphical chip on glass liquid crystal, Alphanumeric, 

16 characters x 3 rows + 2 lines of icons.

Illumination

1 LED for the LCD

8 LEDs for the keypad (Green)

1 LED Incoming call (Green)

1 Charging LED (Red)

Keys

16-key Keypad, Navigation key.

SIM

Plug-in type only

External DC Supply 
Voltage

5.8 V

Battery

3.7 V nominal, 650mAh, Li-Ion

Standby Time

150 hrs maximum

Talk Time

360 minutes maximum

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not 
contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or 
repair the product or products dealt with in this service manual by anyone else could result in serious injury or death.

Содержание EB-GD75























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды