background image

20

(EN)

About This Adaptor

 

„

Overview

This adaptor serves as an interface required to connect a central control device 

such as an intelligent controller with a room air conditioner. Using this adaptor 

can operate or monitor the room air conditioner from the central control device. 

Panasonic room air conditioners equipped with the CN-CNT terminal are supported.

 

„

Capacity setting on the central control device side

When calculating the proportional distribution on the central control device, 

set the capacity of the room air conditioner on the central control device side.

 

„

Alarm indications

If an abnormality is detected by this adaptor, any of the following alarms is 

displayed on the central control device.

• 

C14:  An alarm has occurred on the room air conditioner 

For details of the alarm, check the operating instructions of the room air conditioner.

• 

C15:  Abnormal communication between this adaptor and room air conditioner 

Check the wiring condition.

• 

C19:  Duplication of the adaptor address 

Set the address switch not to duplicate the adaptor address.

 

„

Features

 

z

The following operations from the central control device can be performed.

 

z

Operations to start/stop the room air conditioner, switch the operation 

mode, and set the temperature, fan speed and fan direction (up/down).

 

z

Monitoring the operation status and abnormality of room air conditioner.

 

z

Prohibiting the remote control operation of room air conditioner

 

z

Using ON/OFF contact of external connection can start/stop the room air 

conditioner, prohibit/permit the remote control operation, and perform the  

emergency stop. A coin timer or card key can also be connected.

 

z

Retrieving the operation signal or abnormal signal of room air conditioner  

(An external power source (DC12V) is separately required).

 

„

Restricted matters for controlling the room air 

conditioner from the central control device

 

z

The group control is not possible.

 

z

Temperature setting range: 16°C to 30°C

 

z

The energy-save function, quiet operation function and demand function 

cannot be set.

 

z

The outdoor unit status, and the fan or sensor status of indoor unit cannot 

be monitored.

 

z

Room air conditioner-specific functions (iAUTO-X, NANOE-G, MILD DRY,

 

POWERFUL, QUIET, AIR SWING (◄/►) etc.) cannot be set.

 

z

Room air conditioner-specific functions may be cancelled by operating the 

central control device.

ENGLISH

Содержание CZ-CAPRA1











Отзывы: