Panasonic CS-MS12SD3H Скачать руководство пользователя страница 56

Страница: 56 / 78

13.5.14 H98 (Error Code Stored in Memory and no alarm is triggered / no TIMER LED

flashing)

Malfunction Decision Conditions



Indoor high pressure is detected when indoor heat exchanger is detecting very high temperature when the unit is

operating in heating operation.



Phenomena: unit is stopping and re-starting very often in heating mode.

Malfunction Caused



Indoor heat exchanger thermistor



Clogged air filter or heat exchanger



Over-bent pipe (liquid side)

Troubleshooting

YES

When abnormality indication starts again

Check the indoor unit intake air filter

Is the air filter dirty?

●

Clean the air filter

●

Clean the indoor unit heat exchanger

YES

Check the dust accumulation on the indoor unit heat exchanger

Is the indoor unit heat exchanger dirty?

●

Defect in indoor pipe temperature

Check the indoor pipe temperature thermistor:

●

Check the piping & installation condition

YES

Is the measured resistance of the indoor pipe temperature

●

Plug out connector (CN-TH) from the indoor unit PCB

●

Measure the resistance of the indoor heat exchanger

temperature thermistor

thermistor matches the value specified in its characteristic
chart?

thermistor

●

Replace the indoor pipe temperature
thermistor

●

Replace piping / reinstall the unit
if necessary

For safety reason and to prevent
component breakdown, always switch
off the power before remove and
connect the component.

Caution

Содержание CS-MS12SD3H















































































Результаты поиска

Содержание CS-MS12SD3H

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-MS12SD3H, Руководство по обслуживанию

Результаты поиска

Содержание CS-MS12SD3H

Отзывы:

Бренды по названию

Популярные бренды