Panasonic CS-MS12SD3H Скачать руководство пользователя страница 55

Страница: 55 / 78

13.5.13 H97 (Outdoor Fan Motor – DC Motor Mechanism Locked)

Malfunction Decision Conditions



The rotation speed detected by the Hall IC during fan motor operation is used to determine abnormal fan motor.

Malfunction Caused



Operation stops due to short circuit inside the fan motor winding.



Operation stops due to breaking of wire inside the fan motor.



Operation stops due to breaking of fan motor lead wires.



Operation stops due to Hall IC malfunction.



Operation error due to faulty outdoor unit PCB.

Troubleshooting

When abnormality indication starts again

Turn off power supply and rotate fan by hand

●

Replace fan motor

Does fan rotate smoothly?

Turn power supply on and operate fan

●

Replace outdoor PCB

●

Replace fan motor

Turn off power supply and disconnect fan motor connector,
then turn power on

Does it rotate?

Stop fan motor

Check the rotation feedback output from fan motor

Rotate the fan motor by hand, is the rotation feedback
voltage 15Vdc (pin 1 & 4) generated?

Check the output of fan motor from outdoor PCB

Is the motor power supply voltage ~325Vdc (pin 7 & 4)
generated?

YES

Is the motor control voltage 15Vdc (pin 3 & 4) generated?

Operate the fan, is the rotation command voltage 1~5Vdc (pin 2
& 4) generated?

YES

For safety reason and to prevent
component breakdown, always switch
off the power before remove and
connect the component.

Caution

Содержание CS-MS12SD3H















































































Результаты поиска

Содержание CS-MS12SD3H

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-MS12SD3H, Руководство по обслуживанию

Результаты поиска

Содержание CS-MS12SD3H

Отзывы:

Бренды по названию

Популярные бренды