manualshive.com logo in svg

Panasonic CS-MS12SD3H, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-MS12SD3H Скачать руководство пользователя страница 42

42 

Diagnosis 

display 

Abnormality / Protection control 

Abnormality  

Judgment 

Emergency 

Operation 

Primary location to verify 

F96 

IPM (power transistor) overheating 
protection 

─

 

─

 

  Excess refrigerant 

  Improper heat radiation 

  IPM (Power transistor) 

F97 

Outdoor compressor overheating 
protection 

4 times occurrence

within 20 minutes 

─ 

  Insufficient refrigerant 

  Compressor 

F98 

Total running current protection 

3 times occurrence

within 20 minutes 

─ 

  Excess refrigerant 

  Improper heat radiation 

F99 

Outdoor Direct Current (DC) peak 
detection 

7 times occurrence

continuously 

─ 

  Outdoor PCB 

  IPM (Power transistor) 

  Compressor 

Note: 
“○” – Frequency measured and fan speed fixed. 
“ * ” – For cooling only model, it is the indication when indoor heat exchanger sensor or indoor air intake sensor has 
abnormality. 
 
The memory data of error code is erased when the power supply is cut off, or press the Auto Switch until “beep” 
sound heard following by pressing the “CHECK” button at Remote Control. 
Although operation forced to stop when abnormality detected, emergency operation is possible for certain errors 
(refer to Error Codes Table) by using Remote Control or Auto Switch at indoor unit. However, the Remote Control 
signal receiving sound is changed from one “beep” to four “beep” sounds. 
 

Содержание CS-MS12SD3H















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды