background image

17

How to install the air clean filter

The air clean filter needs to be installed behind the anti-mold filter.

Open the front panel and remove the anti-mold filters, then install 

the air clean filter in the position shown in the figure. After that, 

remount the anti-mold filters and close the front panel.

How to clean the air clean filter

• In general, the filter should be sucked to remove dust in low fan 

speed of a vacuum cleaner once every three months.

• If there is heavily grime on the filter, soak the filter in lukewarm 

water with neutral detergent diluted 1:500 for 1 to 2 minutes then 

wash it.

• Rinse the filter in clean water, then let it dry on the towel in room 

temperature.

• Do not bend nor give excessive force onto the air clean filter.

• If the filter surface is heavily blocked with dirt or damaged, 

replace it with new one. Purchase a replacement filter at your 

local dealer. (model 

CZ-SA1U

)

Cleaning the main unit and remote controller

• Wipe clean using a soft, dry cloth.

• To remove stubborn dirt, moisten a cloth in warm water no hotter 

than 40 °C, wring thoroughly, and then wipe.

• The front panel can be removed in order to wash it with water.

Removing and remounting the front panel
1.

Open the front panel until it is nearly horizontal, grasp the 

sections near the front panel arms on both sides, and then pull 

forward to remove the front panel.

2.

Grasp the sections near the front panel arms on both sides, 

and hold the front panel so that it is nearly horizontal. Then 

push firmly until the arm shafts click into place. After closing the 

front panel, press firmly on the parts indicated by the arrows to 

securely fasten the panel in place.

Also refer to the figure that shows “How to replace the anti-

mold filter”.

Washing the front panel with water

• Clean the front panel gently using a soft sponge, or the like. 

Then wipe away any remaining moisture.

• Neutral detergent may be used to remove stubborn dirt. Then 

rinse thoroughly with water and wipe away any remaining 

moisture.

TROUBLESHOOTING (BEFORE 
CALLING FOR SERVICE)

If your air conditioner does not work properly, first check the 

following points before requesting service. If it still does not work 

properly, contact your dealer or service center.

OPERATING RANGE

The air conditioner is operable within the temperature ranges as 

listed below:

NOTE

When using a footstool or the like, be 
careful not to let it tip over.

Air clean filter

CAUTION

Trouble 

Possible Cause 

Remedy

Air conditioner does 

not run at all.

1. Power failure. 

1. Restore power.

2. Leakage circuit 

breaker tripped.

2. Contact service 

center.

3. Line voltage is too 

low.

3. Consult your 

electrician or 

dealer.

4. Batteries in remote 

controller have run 

down.

4. Replace batteries.

OPERATION lamp 

blinks and air 

conditioner does not 

operate.

Trouble in system.

Contact service 

center.

Compressor runs but 

soon stops.

Obstruction in front of 

condenser coil.

Remove obstruction.

Poor cooling (or 

heating) 

performance.

1. Dirty or clogged air 

filter.

1. Clean air filter to 

improve airflow.

2. Heat source or 

many people in 

room.

2. Eliminate heat 

source if possible.

3. Doors and/or 

windows are open.

3. Shut them to keep 

the heat (or cold) 

out.

4. Obstacle near air 

intake or air 

discharge port.

4. Remove it to 

ensure good 

airflow.

5. Thermostat is set 

too high for cooling 

(or too low for 

heating).

5. Set the 

temperature lower 

(or higher).

6. (Outdoor 

temperature is too 

low for heating.) 

6. (Consult your 

dealer or try to use 

another heat 

appliance.)

Clicking sound is 

heard from the air 

conditioner.

In heating or cooling 

operation, any plastic 

parts may expand or 

shrink due to a 

sudden temperature 

change. In this event, 

a clicking sound may 

occur.

This is normal, and 

the sound will soon 

disappear.

OPERATION lamp 

lights but outdoor unit 

will not run.

The use of cellular 

phones near the air 

conditioner may 

cause disturbance to 

its normal operation.

1. Turn off the power 

then restart the air 

conditioner after a 

while.

2. Consult your 

dealer.

Temperature  Indoor air 

temperature 

Outdoor air 

temperature

COOLING Max. 

32 °C DB / 

23 °C WB 

43 °C DB

Min. 

19 °C DB / 

14 °C WB 

–10 °C DB

HEATING

Max. 

27 °C DB

24 °C DB / 

18 °C WB

Min. 

16 °C DB

– DB/ –15 °C WB

01_85264181224000_EN.fm  Page 17  Monday, January 30, 2012  12:30 PM

Содержание CS-ME18NKE





















Отзывы: