Panasonic CS-E12RB4UW Скачать руководство пользователя страница 84

Страница: 84 / 109

15.4.24 F99 (DC Peak Detection)

Malfunction Decision Conditions

During startup and operation of cooling and heating, when inverter DC peak data is received by the outdoor internal
DC Peak sensing circuitry.

Malfunction Caused



DC current peak due to compressor failure.



DC current peak due to defective power transistor(s).



DC current peak due to defective outdoor unit PCB.



DC current peak due to short circuit.

Troubleshooting

For safety reason and to prevent component
breakdown, always switch off the power
before remove and connect the component.

Outdoor electronic circuit defect due to
power transistor short.

Excessive amount of refrigerant.

Replace the outdoor unit PCB.

Compressor defective due to
mechanical locked.
Replace compressor.

Compressor defective due to winding
shorted.
Replace compressor.

Amplification IC defect.
Diode defect.
Defect in microcontroller.
Replace the outdoor unit PCB.

When abonormality indication starts again.

Reset the error code and turn on the unit
again.

Is there no change even if all refrigerant
is discharged?

Are the compressor’s winding resistance
(U-V, V-W or U-W) shorted?

Is there a sound when compressor starts?

Is compressor vibration even?

YES

Turn off the power and disconnect
the harnesses U, V and W.
Measure the winding resistance
between U-V, V-W and W-U.

Check the compressor winding resistance:

NO (Compressor stops)

NO (Normal)

NO (Quite a lot of vibration at
start operation)

YES (Stops after 2, 3 seconds
of noise during operation)

Caution

Содержание CS-E12RB4UW














































































































Результаты поиска

Содержание CS-E12RB4UW

Отзывы:

Похожие инструкции для CS-E12RB4UW

Бренды по названию

Популярные бренды

Panasonic CS-E12RB4UW, Руководство по обслуживанию

Результаты поиска

Содержание CS-E12RB4UW

Отзывы:

Похожие инструкции для CS-E12RB4UW

Бренды по названию

Популярные бренды