Panasonic CS-A18DKD Скачать руководство пользователя страница 55

Страница: 55 / 86

(Lack of refrigerant in the refrigeration cycle)

Procedure:

Confirm that both the 2-way and 3-way valves are set to
the open position.

Connect the charge set to the 3-way valve’s service
port.

•

Leave the valve on the charge set closed.

•

Connect the charge hose with the push-pin to the
service port.

Connect the charge set’s centre hose to refrigerant
reclaiming equipment.

•

Purge the air from charge hose.

Open the valve (Low side) on the charge set and
discharge the refrigerant until the gauge indicates 0.05
MPa (0.5 kg/cm

G) to 0.1 MPa (1 kg/cm

G).

•

If there is no air in the refrigeration cycle (the pressure
when the air conditioner is not running is higher than 0.1
MPa (1 kg/cm

G), discharge the refrigerant until the

gauge indicates 0.05 MPa (0.5 km/cm

G) to 0.1 MPa (1

kg/cm

G). If this is the case, it will not be necessary to

apply a evacuation.

•

Discharge the refrigerant gradually; if it is discharged
too suddenly, the refrigeration oil will also be
discharged.

Turn on refrigerant reclaiming equipment.

11.1.4. Balance refrigerant of the 2-way, 3-way valves

CS-A18DKD CU-A18DKD / CS-A24DKD CU-A24DKD

Содержание CS-A18DKD























































































Результаты поиска

Содержание CS-A18DKD

Отзывы:

Бренды по названию

Популярные бренды

Panasonic CS-A18DKD, Руководство по обслуживанию

Результаты поиска

Содержание CS-A18DKD

Отзывы:

Бренды по названию

Популярные бренды