manualshive.com logo in svg

Panasonic CS-A18DKD, Руководство по обслуживанию

Поделиться
Скачать
Panasonic CS-A18DKD Скачать руководство пользователя страница 47

HOW TO TAKE OUT FRONT GRILLE

Please follow the steps below to take out front grille if
necessary such as when servicing.
 1. Open the intake grille.
 2. Set the vertical airflow direction louver to the horizontal

position.

 3. Slide down the 3 caps on the front grille as shown in the

illustration below, and then remove the 3 mounting screws.

 4. Pull the lower section of the front grille towards you to

remove the front grille.

When reinstalling the front grille, first set the vertical
airflow direction louvers to the horizontal position and
then carry out above steps 2 - 3 in the reverse order.

AUTO SWITCH OPERATION

The below operations will be performed by pressing the
“AUTO” switch.
 1. AUTO OPERATION MODE

The Auto operation will be activated immediately once the
Auto Switch is pressed.

 2. TEST RUN OPERATION (FOR PUMP DOWN/SERVICING

PURPOSE)
The Test Run operation will be activated if the Auto Switch
is pressed continuously for more than 5 sec. A “beep”
sound will occur at the fifth sec., in order to identify the
starting of Test Run operation.

 3. REMOTE CONTROLLER RECEIVING SOUND ON/OFF

The ON/OFF of remote controller receiving sound can be
changed over by the following step:
 a. Release the Auto Switch after Test Run operation is

activated.

 b. Then, within 20 sec after (a), press Auto Switch for more

than 5 sec.
A “beep” “beep” sound will occur at the fifth sec., then
release the Auto switch.

 c. Within 20 sec after (b), press Auto Switch again.

Everytime Auto Switch is pressed (within 20 sec
interval), remote controller receiving sound status will be
reversed between ON and OFF.
Long “beep” sound indicates that remote controller
receiving sound is OFF.
Short “beep” sound indicates that remote controller
receiving sound is ON.

47

CS-A18DKD CU-A18DKD / CS-A24DKD CU-A24DKD

Содержание CS-A18DKD























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды