16
E
N
G
L
I
S
H
19
CQ-RD243N
15
E
N
G
L
I
S
H
CQ-RD243N
18
A
B
A4:
A5:
A8:
A7:
A5 A7 A8 A4
A5*:
B7
B8
B5
B6
B3
B4
B1
B2
B7:
B8:
B5:
B6:
B3:
B4:
B1:
B2:
(Green)
(Green w/black stripe)
(White)
(White w/black stripe)
(Gray)
(Gray w/black stripe)
(Violet)
(Violet w/black stripe)
(Red)
(Black)
(Blue w/white stripe)
(Yellow)
(Blue w/white stripe)
Extension Cord
(DIN/BATT/RCA/GND)
(Black)
CD Changer (Option)
CX-DP880N
Ground Lead
To a clean, bare metallic
part of the car
chassis
(Yellow)
Fuse (3A)
Battery Lead
To the car battery,
continuous
+12V DC
Supplied for an
optional CD Changer.
Cassette Receiver
CQ-RD243N
e
Power and
Speaker
Connector
Antenna
ISO Antenna
Conversion Cord
(Option)
(If needed)
(L)(White)
(L)(White)
(R)(Red)
CD Changer
Input Connector
Pre-Amp.Out
Connector
(Rear)
DIN Cord
RCA Cord
RCA Cord
(R)(Red)
CD Changer
Control Connector
BATTERY 15A
ACC
Cautions:
¡
Check the connectors provided on your car (see precaution below) before connecting the system.
¡
This unit is designed for use in a car having a 12-volt negative ground battery system.
¡
To prevent damage to the unit, be sure to follow the connection diagram.
¡
Strip about 5 mm of the lead ends for connection (only non-ISO connector cords).
¡
Do not insert the power connector into the unit until the wiring is completed.
¡
Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and prevent
cable terminals from touching any metal parts.
Electrical Connections
If the fuse (rear panel) blows frequently, they
may be something wrong with the unit.
Consult your nearest Panasonic Service
Centre for service.
¡
This unit can be connected to an
optional CD changer (CX-DP880N,
CX-DP9061/DP9060EN, CX-
DP88N, CX-DP801/DP803EN or
CX-DP601EN) and optional exten-
sion cord.
¡
For details consult your nearest
authorized Panasonic Dealer.
¡
For connection to a CD changer,
refer to the operating instructions
of the CD changer (CX-DP880N,
CX-DP9061/DP9060EN, CX-
DP88N, CX-DP801/DP803EN or
CX-DP601EN).
Fuse (15 A)
To remove the Fuse
Precautions (ISO Connector)
¡
The pin arrangement of the power connector
conforms to ISO standard.
¡
The pin arrangement of ISO connectors in some
cars may differ from the ISO standard.
¡
Please check that the pin arrangement of the
connector in your car conforms to ISO standard.
¡
For car types A and B, change the wiring of the
red and yellow leads as shown at below.
¡
After connection, insulate the portions marked
(
C
) with insulating tape.
Note:
For cars other than types A and B, please
consult your local car shop.
C
C
BATTERY 15A
ACC
ISO
Standard ISO
C
C
BATTERY 15A
ACC
A
Car Type A
ACC
C
C
B
Car Type B
BATTERY 15A
A7: IGN or ACC switched 12 V supply
(Red)
(Yellow)
(Yellow)
(Red)
(Red)
(Yellow)
(Yellow)
(Red)
(Red)
(Yellow)
(Red)
(Yellow)
A4: IGN or ACC switched 12 V supply
A4: +12 V Battery (Permanent supply)
A7: +12 V Battery (Permanent supply)
A7: +12 V Battery (Permanent supply)
A4: No connection
A7
A4
1
Fuse
e
Power and
Speaker
Connector
3
2
Note:
The power antenna extends automatically when
the power of this unit is turned on.
A5
: Motor Antenna Relay Control Lead
(Blue w/white stripe)
To Motor Antenna (Max. 500mA)
This lead is not intended for use with a switch actuated
power antenna.
A7
: Power Lead (ACC or IGN) (Red)
To ACC power, +12 V DC.
A8
: Ground Lead (Black)
To a clean, bare metallic part of the car chassis.
A4
: Battery Lead (Yellow)
To the car battery, cont12 V DC.
C1
: External Mute Lead
(Orange) (not used)
C3
: External Remote Control Lead
(Brown w/black stripe)
When using a non-Panasonic external remote control, refer
to the manufacture for their product before connecting.
A5*:
This lead can be used as either Amp.Relay Control Power Lead or Motor Antenna Relay Control Lead, or both at the
same time. However, the current capacity of this lead is 500 mA.
Left (+)
Left (–)
Left (+)
Left (–)
Right (+)
Right (–)
Right (+)
Right (–)
Rear
Front
Front
Rear
ISO Connector
Speakers
