INF-15
11. Software Version Upgrade Method
1. MICROCOMPUTER (FLASH) / PLD CHART
Circuit board
name
Name
Connector/
SW Pos.
Maker Reference
CAM SOFT (IN)
HItachi
CAM SOFT (OUT)
9P / No.1
Fujitsu
CAM TABLE
9P / No.1
Fujitsu
FONT ROM
9P / No.1
Fujitsu
PLD (CHAR) : CHAR FPGA On board
Actel
CAM DSP
PLD (MEM) : FM FPGA
8P / No.E
ALTERA
PULSE
PLD (TG) : PULSE PLD
On board
ALTERA
<SOFTWARE VERSION DISPLAY METHOD>
1)
PUSH Menu SW longer than 3 sec. so
that Main Menu appears on the VF.
2)
Execute following steps so that software
version of CAMERA can be displayed.
MAIN MENU
→
MAINTENANCE
→
DIAGNOSTIC
ECC SYS
VTR SYSCON
9P / No.5
Mitsubishi
SERVO SERVO
9P
/
No.3
Matsushita
Audio LCD
FRONT (LCD)
9P / No.7
Mitsubishi
ECC SYS
VIDEO FPGA (PREREC)
8P / No.F
ALTERA
VTR CODEC PREPROCESS FPGA
Actel
<SOFTWARE VERSION DISPLAY METHOD>
1)
PUSH Menu SW longer than 3 sec. so
that Main Menu appears on the VF.
2)
Execute following steps so that software
version of VTR can be displayed.
MAIN MENU
→
VTR MENU
→
VTR DIAG
: These are not required for version upgrade.
2. Connection
Open the left side panel. There are an RS-232C port, an 8pin-PLD connector and a rotary switch.
Choose an appropriate terminal and setting of the rotary switch according to each description.
3. Rotary switch setting
0:
Default (Operation mode)
1:
Write Camera u-com
2:
Communicate with Camera u-com
3:
Write Servo u-com
4:
Communicate with Servo u-com
5:
Write VTR u-com
6:
Communicate with VTR u-com
7:
Write AUDIO/LCD u-com
8:
Communicate with AUDIO/LCD u-com (1)
9:
Communicate with AUDIO/LCD u-com (2)
A:
Communicate with AUDIO/LCD u-com (3)
E:
Write Camera FPGA
F:
Write VTR FPGA
4. Software version-up procedure
<CAM SOFT (OUT)>
1. Connect a PC and AJ-SDX900 with an RS-232C cross cable (9P-9P).
2. Set the rotary switch to
1 position
.
3. Turn on both PC and AJ-SDX900.
4. Execute ‘K96_Cam_W.bat’ so that version-up program starts.
5. Erase, Write and Verify are automatically performed.
6.
If a communication error occurs, check the rotary switch setting and the power on both PC and
Camcorder.
7. When it is completed, press any key to quit the program.
8. Turn off the PC and Camcorder.
9. Remove the RS-232C cable and return the rotary switch to 0 position.
Содержание AJ-D908MC
