ELE-13
2-22. Pre Clip Voltage Adj.
(P mode)
BOARD
PREAMP Board
TP
TP502 (B), TP302 (G), TP102 (R),
ADJ.
EVR
F No.
Adjustment
CHART
Gray Scale
MODE
CAM
M. EQ.
Monitor TV, Oscilloscope
SPEC.
Saturation Level = more than 250%
1. Click
the
“21. Pre Clip Voltage Adjustment P mode”
of the camera adjustment software.
2. Connect a scope to
TP502 (B), TP302 (G), TP102 (R)
.
3. Shoot a Gray Scale Chart and adjust the IRIS so that
the video level of the VIDEO OUT becomes 100% at
the white portion.
4. Measure the level of
TP502 (B), TP302 (G), TP102 (R)
(about 400mV) and note it.
5. Set the IRIS to
“F5.6”
.
6. Adjust the Slider on the PC so that the saturation level
(A) of the
B
signal (
TP502
) becomes more than
2.5
times
(250%) from 100% level (measured in step 4)
and no saturation blurs (curve) as shown in Figure.
7. Click
“>>”
.
8. Adjust the Slider on the PC so that the saturation level
(A) of the
G
signal (
TP302
) becomes more than
2.5
times
(250%) from 100% level (measured in step 4)
and no saturation blurs (curve) as shown in Figure.
9. Click
“>>”
.
10. Adjust the Slider on the PC so that the saturation level
(A) of the
R
signal (
TP102
) becomes more than
2.5
times
(250%) from 100% level (measured in step 4)
and no saturation blurs (curve) as shown in Figure.
11. Click
“>>”
.
2-23. Pre Clip Carrier Adj.
(P mode)
BOARD
PREAMP Board
TP
VIDEO OUT
ADJ.
EVR
F No.
F5.6
CHART
Gray Scale
MODE
CAM
M. EQ.
Waveform Monitor
SPEC.
Minimum
1. Click
the
“22. Pre Clip Voltage Adjustment P mode”
of the camera adjustment software.
2. Connect a waveform monitor to
VIDEO OUT
.
3. Shoot a Gray Scale Chart.
4. Set the IRIS to
“F5.6”
.
5. Set the gain of waveform monitor to 5X.
6. Adjust the Slider on the PC so that the level
“A”
becomes minimum as shown below.
7. Click
“>>”
.
8. Adjust the Slider on the PC so that the level
“A”
becomes minimum as shown below.
9. Click
“>>”
.
10. Adjust the Slider on the PC so that the level
“A”
becomes minimum as shown below.
11. Click
“>>”
.
12. After compleate the adjustment, click
“NORMAL 60I
(for NTSC)
” or “NORMAL 50I
(for PAL)
”
.
A
A
VIDEO OUT
Saturation Blurs
A
Clip Saturation Blurs
Содержание AJ-D908MC
