manualshive.com logo in svg

Panasonic AFP7CPS31, Руководство пользователя

Поделиться
Скачать
Panasonic AFP7CPS31 Скачать руководство пользователя страница 86

 

8-10 

Specifications

 

 

8.1.5  List of System Relays 

WS0 

Device  

number 

Name 

Description 

SR0 

Self-diagnostic error flag 

Turns on when a self-diagnosis error occurs. Self-diagnosis error 
codes are saved in the system data register SD0. 

SR1 

Unit alarm occurrence 

Turns on when a unit alarm is detected. The slot number of the unit 
where an alarm has occurred is saved in the system data register 
SD1. 

SR2 

Unit error occurrence 

Turns on when a unit error is detected. The slot number of the unit 
where an error has occurred is saved in the system data register 
SD2. 

SR3 

Unit warning occurrence 

Turns on when a unit warning is detected. The slot number of the 
unit where a warning has occurred is saved in the system data 
register SD3. 

SR4 

Unit verification error 
occurrence 

Turns on when an I/O verification error is detected. The slot number 
of the unit where an I/O verification error has occurred is saved in 
the system data register SD4. 

SR5 

Unit installation error 
detection 

Turns on when a unit installation error is detected. The slot number 
of the unit where an I/O verification error has occurred is saved in 
the system data register SD5. 

SR6 (Not 

used) 

 

SR7 

Operation error flag  
(hold type) 

Turns on when an operation error occurs after the unit has started 
operating, and remains on while the unit operation continues. The 
PB number where an error has occurred is saved in the system 
data SD7, and the address is saved in system data registers SD8 to 
SD9. It indicates the first operation error that has occurred. 

SR8 

Operation error flag  
(latest type) 

Turns on every time an operation error occurs. The PB number 
where an operation error has occurred is saved in the system data 
register SD10, and the address is saved in system data registers 
SD11 to SD12. Every time a new error occurs, the data are 
updated. It does not turn off even if the instruction is normally 
completed after the occurrence of the error(s). In order to check if 
any error has occurred in a specific instruction, either see address 
data saved in the SD, or clear error flags using ERR instruction 
immediately before the specific instruction, and check flags 
immediately after executing the instruction. 

SR9 

Carry flag (CY flag) 

Used in shift instruction and rotate instruction with a carry flag. The 
flag can also be operated in carry set instruction and carry reset 
instruction. It is not set in overflow or underflow of operation results. 

SRA 

> flag 

Executes comparison instruction, and turns on if the result is larger. 

SRB = 

flag 

Executes comparison instruction, and turns on if the result is equal.  
Executes operation instruction, and turns on if the result is '0'. 

SRC < 

flag 

Executes comparison instruction, and turns on if the result is 
smaller. 

SRD 

Support timer instruction 
flag 

Turns on after support timer instruction (SPTM) is executed and 
subsequently specified time has passed. Turns off when execution 
conditions go off. 

SRE 

All error alarms relay 

Turns on when any of the error alarm relays E0 to E4095 turns on. 
Turns off once all of the error alarm relays go off. 

SRF 

Constant scan error 
flag 

Turns on if scan time exceeds the setting during constant scan. It 
also turns on if '0' is set in FP7 configuration. 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS31














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды