Panasonic AFP7CPS31 Скачать руководство пользователя страница 52

Страница: 52 / 109

5-6

Operation

5.2.3 Data Hold During Power Failure

The FP7 CPU unit backs up most data into ROM (non-volatile memory).



Data saved in ROM (non-volatile memory)

• Project data (programs, configuration data, comments)

• Hold type data in the operation memory

• System monitors, system records data (e.g. lifetime data, error records)



Data held by the built-in capacitor and the backup battery

• Calendar timer

KEY POINTS



Calendar timer values can continue operation for about one week by the
built-in capacitor, even if no battery is used.



In order to charge the built-in capacitor, supply power to the CPU unit for at
least 30 minutes.

5.2.4 Online Editing

The FP7 CPU unit can be edited online. Usable operations vary by mode.



PROG. mode

• While editing a program, the program inside the RAM is rewritten by PG converting a given
network inside the program block that is being edited.

• Rewritten data in the RAM is incorporated into the ROM1.

• Comments and configuration data can also be rewritten.



RUN mode

• While editing a program, the program is written into the RAM by PG converting a given
network inside the program block that is being edited.

• Rewritten data in the RAM is incorporated into the ROM1.

• Configuration data cannot be rewritten.

• Comments can be rewritten.

• It is not possible to download the entire project.

• It is possible to download the Program Block (PB).

After a program is rewritten in the RUN mode, operation stops for a time length proportionate
to the size of the relevant PB.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS31














































































































Результаты поиска

Содержание AFP7CPS31

Отзывы:

Бренды по названию

Популярные бренды

Panasonic AFP7CPS31, Руководство пользователя

Результаты поиска

Содержание AFP7CPS31

Отзывы:

Бренды по названию

Популярные бренды