Panasonic AFP0HC32ET Скачать руководство пользователя

Страница: 5 / 102

Glossary

iii

Term

Description

Communication Method
(Tag/Instance)

For connecting from an originator to target, there are two methods to specify the

device area of the target.

- by specifying numbers (Instance)

- by specifying symbols (Tag).

When setting connections, the methods available for each target are displayed.
For using the FP0H as a target, either method can be selected.

However, the selectable instance numbers for the instance method are 100 to 199.

Input Send Trigger

The transmission timing is selected from Cyclic or COS (Change of state).

However, COS depends on devices.

COS is basically a cyclic communication, however, it also performs transmission

when sent data changes.

The FP0H does not support COS.

COS Transmission

Disable Time

Transmission disable time (RPI of input information x 1/4) is displayed when "Input

Send Trigger" is set to "Change of State (COS)".

Even if the unit detects the change in data, it is not sent within the transmission

disable time.

Timeout Period

In the cyclic communication, transmission data is sent as UDP packet. The timeout is

judged on a receiver side.

The timeout period is selected from 4, 8, 16, 32, 64, 128, 256 and 512 times of RPI.

The timeout period should be 10 msec or more.

RPI can be specified for T>O direction and O>T direction separately, so each timeout

period may be different values.

Input Information (T>O)

This is the setting for the transmission from a target to the FP0H (originator).

Output Information

(O>T)

This is the setting for the transmission from the FP0H (originator) to a target.

RPI
(Requested

Packet

Interval)

Set the transmission interval for the cyclic communication. Set a value within the

communication capacity of a target. The usable RPI range depends on devices.
For the FP0H, it is 1 ms to 10 s (by 0.5 ms).

Point to Point
(1:1 communication)

One to one communication is performed between an originator and a target.

Transmitted packets are received only by each other.

Other devices connected to the same HUB do not receive those transmission

packets.

Multicast
(Multicast

communication)

Transmission data is sent as a multicast packet. By connecting multiple originators to

one target, one multicast packet can be received by multiple originators.
(Note) Multicast packets are basically received by all devices connected to the same

HUB which includes the devices unrelated to the communication, and it leads to an

unnecessary communication load.
When using the multicast communication, set not to exceed 100% by the load factor

calculation of the setting tool.

TTL

TTL (Time To Live) is used to set the hierarchies of the network in which transmission

packets can exist when sending multicast packets to other PLCs.

Instance ID/Tag name

Set an instance ID or tag name according to the communication method of the

selected connection.

Data Size

The data sizes of the originator and target for the cyclic communication must be the

same. When they do not match, the communication cannot be performed.

Parameter setting

Data size, instance ID and other parameters that can be changed in the EDS file can

be changed.

PPS performance index
(Packet per sec)

This is an index of sent/received packets processed in one second.

Содержание AFP0HC32ET







































































































Результаты поиска

Содержание AFP0HC32ET

Отзывы:

Похожие инструкции для AFP0HC32ET

Бренды по названию

Популярные бренды

Panasonic AFP0HC32ET, Руководство пользователя

Результаты поиска

Содержание AFP0HC32ET

Отзывы:

Похожие инструкции для AFP0HC32ET

Бренды по названию

Популярные бренды