Panasonic AFP0HC32ET Скачать руководство пользователя | Manualshive

Страница: 2 / 102

background image

SAFETY PRECAUTIONS

To prevent accidents or personal injuries, please be sure to comply with the following items.

Prior to installation, operation, maintenance and check, please read this manual carefully for proper use.

Before using, please fully understand the knowledge related to the equipment, safety precautions and all

other precautions.

Safety precautions are divided into two levels in this manual: Warning and Caution.

WARNING

Incorrect operation may lead to death or serious injury.

● Take appropriate safety measures to the external circuit of the product to ensure the security of

the whole system in case of abnormalities caused by product failure or external.

● Do not use this product in areas with inflammable gases.

Otherwise it may lead to an explosion.

● Do not put this product into a fire.

Otherwise it could cause damage to the battery or other electronic parts.

● Do not impact, charge or heat the lithium battery, and do not put it into a fire.

Otherwise it may lead to fire or damage.

CAUTION

Incorrect operation may lead to injury or material loss.

● To prevent the excessive exothermic heat or smoke generation of the product, a certain margin is

required for guaranteed characteristics and performance ratings of relative products.

● Do not decompose or transform it.

Otherwise it will lead to the excessive exothermic heat or smoke generation of the product.

● Do not touch terminal blocks during power-on.

Otherwise it may result in an electric shock.

● Set an emergency stop and interlock circuit in the external devices.
● Connect wires and connectors reliably.

Otherwise it may lead to the excessive exothermic heat or smoke generation of the product.

● Do not undertake construction (such as connection and disconnection) while the power supply is on.

It could lead to an electric shock.

● If the equipment is used in a manner not specified by the Panasonic, the protection provided by the

equipment may be impaired.

● This product has been developed/produced for industrial use only.

Description on Copyright and Trademarks

● The copyright of this manual is owned by Panasonic Industrial Devices SUNX Co., Ltd.
● Unauthorized reproduction of this manual is strictly prohibited.
● Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.
● Ethernet is a registered trademark of Fuji Xerox Co., Ltd. and Xerox Corporation.
● EtherNet/IP is a registered trademark of ODVA (Open DeviceNet Vendor Association).
● Other company and product names are trademarks or registered trademarks of their respective companies.

PLC_BAT_ET_FP0H

«
1
2
3
4
...
»

Содержание AFP0HC32ET







































































































Отзывы:

Нет отзывов

Похожие инструкции для AFP0HC32ET

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Vaillant Страницы: 11

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: YASKAWA Страницы: 340

Бренд: GHL Страницы: 34

Бренд: Seiko Страницы: 30

ASC G Wi-Fi kit

Бренд: Waeco Страницы: 386

Бренд: A & H Страницы: 35

Бренд: Cypress Страницы: 2

MEMO CORE CONTROL

Бренд: MegaLite Страницы: 11

Бренд: YASKAWA Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды