manualshive.com logo in svg

Panametrics DigitalFlow XGF868i, Руководство по обслуживанию

Поделиться
Скачать
Panametrics DigitalFlow XGF868i Скачать руководство пользователя страница 35

DigitalFlow™ XGF868i Service Manual

27

Chapter 4. Parts Replacement

1.

If necessary, replace the angle bracket on the main board, insert the screw (with flat washer and lock washer), 

and screw it into the standoff on the main board. See 

Illustration 11

 in 

Figure 8 on page 31

.

IMPORTANT:

The small angle bracket on the terminal board must be positioned on the outside of the main board 

with the previously removed nylon washer between them.

2.

Face the 

User Program

 side of the main board toward the rear of the power supply board. Orient the boards so 

that the pins along the bottom of the main board align with connectors J2 and J6 on the power supply board, 

and push the two boards firmly together.

Note:

If the thermal gap filler pad of the power supply board has been damaged, you must remove and replace it 

before reinserting the power supply board. First, remove and discard the damaged pad. Then remove the 

blue protective liner from the new pad and apply it with the white face against the power supply board.

3.

Secure the power supply board and heat sink to the main board by reinstalling the screws, flat washers and lock 

washer previously removed from the corners of the power supply board. See 

Illustration 11

 in 

Figure 8 on page 31

.

4.

Refer back to 

Illustration 7

 in 

Figure 7 on page 30

. Carefully align the terminal board onto the main board/power 

supply assembly and the two option boards (Slot 1 and Slot 2, where applicable), so that the connectors listed in 

Table 5

 below are facing each other. Then, firmly press the terminal board and the interconnect board toward 

each other until all of the connectors are completely seated.

IMPORTANT:

With two option cards installed, it may require some patience to get all of the connectors properly 

aligned. Do not force the assembly together, or some of the pins may not enter the sockets properly.

5.

Secure the assembly together by installing the three mounting screws, flat washers and lock washers previously 

removed from the terminal board. Be sure to install one end of the green grounding jumper wire under the screw 

indicated in 

Illustration 7

 in 

Figure 7 on page 30

. The smaller screw should be used at the angle bracket location, 

and secured with a nut, lock washer and flat washer.

Proceed to the next section for instructions on installing the reassembled circuit board assembly in the electronics 

enclosure.

Table 5: Mating Connectors for Terminal Board

Terminal Board

Mating Board

1

J7 Connector (Large Three-Pin Connector Plug)

Power Tab on AC Power Supply Board

2

J6 Connector (Large Three-Pin Connector Plug)

Power Tab on DC Power Supply Board

3

P7 Connector

J7 Connector on Main Board

4

P10 Connector

J9 Connector on Main Board

5

P9 Connector

J10 Connector on Main Board

6

P8 Connector

J8 Connector on Main Board

7

P21 Connector

J1/J3 Connector on I/O Board, Slot 2 Option

8

P22 Connector

P2 Connector on I/O Board, Slot 1

Содержание DigitalFlow XGF868i









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды