background image

COMMISSIONING 

COMMISSIONING TESTS & ADJUSTMENT PROCEDURES 

 

GAS INLET PRESSURE TEST  

IMPORTANT – 

Check the gas supply pressure at the gas inlet to the heater with all other gas burning appliances in 

the premises operating (burners alight). The minimum gas supply pressures are: 

 

Natural Gas: 1.13 kPa 

 

Propane: 2.75 kPa 

If this minimum cannot be achieved, it may indicate the meter or the gas line to the heater is undersized. It is 
important to ensure that an adequate gas supply pressure is available to the heater when all gas burning appliances 
on the same gas supply are operating. 

The maximum gas pressure must NOT exceed 3.5 kPa. 
 

SETTING HEATER FLUE TYPE 

The controller must be set according to the heater flue type  at time of commissioning. Combustion fan speed  is 
automatically adjusted according to the flue type setting to aid combustion. 

Perform the following procedure to set the heater flue type: 

1. 

Ensure heater is unplugged from power point.

 

2. 

Remove four screws retaining front louvre. Two screws are located on left hand side of louvre and two screws 
are located on right hand side of louvre. Screws are accessed through louvres. 

3. 

Remove front louvre by pulling louvre away from heater. 

4. 

Remove lower front panel by simultaneously depressing tabs located on 
bottom of heater sides and pulling lower front panel away from heater. 

5. 

Remove two screws retaining front panel (screws are located on bottom 
corners of front panel). 

6. 

Remove front panel as follows: Slide front panel to the right, push it down to 
disengage retaining tabs and then pull panel away from heater. 

7. 

Plug heater into power point and switch power point ON. 

8. 

Press and hold controller '

Adjuster Button 2

' for two seconds and release the 

button when the control  panel  display shows the current flue configuration 
setting ('00', '01' or '02'). 

9. 

Press and release the 

▲ or ▼ button to change the flue type setting according 

to the installations flue configuration (refer to 'Flue Type Setting Table'  on 
page 26). 

10.  Press and hold '

Adjuster Button 2

' for two seconds and release the button 

when the control panel display goes blank. The flue type setting has now been 
set. 

11. 

Isolate power supply to heater by unplugging heater from power point.

 

12.  Reassemble heater in reverse order of steps 6 ~ 2. 

 

Flue Type Setting Table (Shaded area = Required flue type setting) 

No. of Bends* 

Total Flue Length (metres) 

00 

00 

00 

01 

01 

01 

02 

02 

02 

00 

00 

01 

01 

01 

01 

02 

02 

02 

00 

00 

01 

01 

01 

02 

02 

02 

02 

3** 

00 

01 

01 

01 

01 

02 

02 

02 

02 

 

* Two 45° bends = 1 bend. 

** Vertical flue terminations only. Flue systems with a horizontal flue termination must not have more than two bends. 

Paloma factory setting is '00'. 

 

26 

 

Содержание PRS-150N





































Отзывы: