6
Palmgren Operating Manual & Parts List 9683127
INSTALLATION (CONTINUED)
Many cover plate screws, water pipes and outlet boxes are not
properly grounded. To ensure proper ground, grounding means
must be tested by a qualified electrician.
EXTENSION CORDS
• The use of any extension cord will cause some drop in voltage
and loss of power.
• Wires of the extension cord must be of sufficient size to carry the
current and maintain adequate voltage.
• Running the unit on voltages which are not within ±10% of the
specified voltage may cause overheating and motor burn-out.
• Use the table to determine the minimum wire size (A.W.G.)
extension cord.
• Use only 3-wire extension cords having 3-prong grounding type
plugs and 3-pole receptacles which accept the tool plug.
• If the extension cord is worn, cut or damaged in any way, replace
it immediately.
WARNING:
This machine must be grounded. To avoid electrocution or
fire, any repairs to electrical system should be done only by a qualified
electrician, using genuine replacement parts.
OPERATION
SAFETY PRECAUTIONS
WARNING:
Always observe the following safety precautions.
• Whenever adjusting or replacing any parts on the band saw
turn, switch off and remove plug from power source.
• Make sure the blade guides are positioned correctly.
• Use the appropriate blade for the workpiece that is being cut.
• Use a sharp blade. Replace dull blades or blades which are
missing teeth.
• Make sure the blade is tensioned properly and going in the right
direction.
• Use the proper blade speed for the work.
• For optimum performance, do not stall the motor or reduce the
speed. Use the proper feed pressure.
• Secure the workpiece in a stable position.
• Check that all guards are attached.
• After turning the switch on, let the blade come to full speed.
• Keep hands away from the blade and all moving parts.
• Always wear eye protection or face shield.
• Always stop the band saw before removing scrap pieces from
table.
• Never attempt to saw stock that does not have a flat surface,
unless a suitable support is used.
• Always hold material firmly and feed it into the blade at a
moderate speed.
• Always turn off the machine if the material is to be backed out of
an uncompleted cut.
• Make sure that the blade tension and blade tracking are
properly adjusted.
• Make “relief” cuts before cutting long curves.
• Release blade tension when the saw will not be used for a long
period of time.
ON/OFF SWITCH
Refer to Figure 11.
WARNING:
Before starting check if any part of your band saw is
missing, malfunctioning, has been damaged or broken, such as the
motor switch, or other operation control, a safety device or the power
cord, turn the band saw off and unplug it until the particular part is
properly repaired or replaced.
The ON/OFF switch is located on the left front of the saw column. To
turn saw ON, pull the switch to the up position. To turn saw OFF,
push the switch to the down position.
The saw can be locked from unauthorized use by locking the switch.
To lock the switch:
1. Turn the switch to OFF position and disconnect saw from power
source.
2. Pull the key out. The switch cannot be turned on with the key
removed.
NOTE:
Should the key be removed from the switch at the ON
position, the switch can be turned off but cannot be turned on
again.
• To replace key, slide key into the slot on switch until it snaps.
ADJUSTMENTS
The blade tracking, tension and blade guides have been properly
adjusted at the factory. However, the adjustments may change while
the saw is in transit.
It is recommended to verify these adjustments before operating
saw.
CHANGING AND ADJUSTING THE SAW BLADE
This band saw is factory-equipped with a general-purpose wood
cutting blade; the saw blade is set prior to delivery.
To change the saw blade, the following procedure must be followed:
WARNING:
To avoid injury from unexpected starting, whenever
changing the saw blade or carrying out adjustments, switch the band
saw off and remove the power cord from the main outlet. To avoid
injury to hands when handling the saw blade, wear gloves whenever
necessary.
1. Remove the rip fence, the guide rail, the wing nut and screw
from the table.
2. Open the upper and lower doors by turning the door locking
knobs.
3. Loosen the tracking lock knob (See figure 13, page 9).
Volts
120
25
50
100
150
240
50
100
150
300
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
More Not
Than
More Than
Minimum Gage for Cord
Total Length of Cord in Feet
Not Recommended
Ampere Rating
Extension Cord Table
Figure 11 - ON/OFF Switch and Key
