5
GETTING STARTED
SAFETY / SPECIFICATIONS
ASSEMBLY / INSTALLATION
OPERATION
TROUBLESHOOTING
MAINTENANCE / REPAIR
SAFETY RULES (CONTINUED FROM PG.3)
Know how to use your tool
Dusty work environments may be
hazardous to your health. Always wear a
OSHA/NIOSH approved, properly fitting face mask or
respirator.
The operation of any power tool can result
in foreign objects being thrown into the
eyes, which can result in severe eye damage. Always wear
safety goggles complying with United States ANSI Z87.1.
Think safety! Safety is a combination of
operator common sense and alertness at
all times when tool is being used.
• The Model 9682905 Grinder / Sharpener Machine is
designed and intended for use by properly trained operators.
You must be familiar with the proper and safe operation of
a Grinders / Sharpener Machine. Obtain proper training and
knowledge before operating this machine.
• Ensure the grinding wheel is solid and free from any flaws or
cracks. You can perform a ring test by holding the grinding
wheel with a wooden dowel rod through the arbor hole and
lightly striking it with a wrench or hammer. The wheel should
emit a clear “ping” sound. A damaged wheel will emit a dull
sound. If there is any doubt of a wheel’s condition, replace it
immediately.
• A damaged wheel is more likely to fly apart or explode
upon machine start up. Do not stand in line with the wheel’s
rotation upon start up.
• Grinding wheels operated at a speed faster than they are
rated for can fly apart or explode causing injury or death.
Before mounting a new wheel make sure the wheel’s RPM
rating is equal to or more than the machine’s RPM rating.
• Heavy impact with a workpiece or trying to make a very deep
cut can cause a wheel to break apart or explode. Do not jam
a workpiece into the wheel to reduce this risk.
• Use the right tool for the job. Do not force a tool or
attachment to do a job for which it was not designed.
• Remove adjusting keys and wrenches. Form a habit of
checking to see that keys and adjusting wrenches are
removed from the machine before turning it on.
• To reduce the risk of electrical shock, never use the tool in
rain or wet environments. Store the tool indoors.
• Turn the tool off immediately in the case of an emergency.
Completely remove the tool from its power source before
attempting to fix the issue.
• Never leave the machine running while it is unattended. Turn
off the power and stay with the machine until it comes to a
complete, full stop.
• Use recommended accessories. Understand and obey all
safety instructions supplied with accessories. The use of
improper accessories may cause injury.
• Make sure that the any hazardous dusts created by grinding
and sharpening are removed by a dust extraction unit.
• Never connect a this machine to a dust collection system
also being used by woodworking machines. The sparks
and hot chips from this machine can quickly ignite the
woodworking dust cause fire or an explosion.
• Some materials such as magnesium, titanium and aluminum
have flammable properties. Consult with the supplier of these
materials for information on safe grinding procedures.
SPECIFICATIONS
Model 9682905 Grinder / Sharpener Machine
Power
115V, 60Hz
Speed Cup Wheel,
Diamond Cup Wheel
5,000 RPM
Max. Grinding Speed
114 FPS
Speed Motor
2,750 RPM
Adjustable Angles
Vertical / Rear
0- 40°
Horizontal / Taper Grinding
0-180°
Negative
0- 52°
Setting Positions Rotation
Angle
15°
180°
Capacities
Tool Holder Travel Length
5.5”
Fine Adjustment Range Of
The Tool Holder
0.070”
Fine Adjustment Range Of
The Length Axis
0.23”
Division Scale Infeed
0.00039”
Grinding Cup Wheels
Corundum Cup Wheel
0100 x 50 x 020
Diamond Cup Wheel
0100 x 50 x 020
Grinding Accessory Capacities
Single Edge Milling Cutter
Up to 0.47” in dia.
Turning Tool
Up to 0.82” x 0.82”
Drill Bit
Up to 0.47 in dia.
End Mill Cutter
Up to 0.47” in dia.
Collets
1/8” to 1/2”
Dimensions H X D X W
13.4” x 17.7” x 13.7”
Net Weight
110 lbs.
ASSEMBLY / INSTALLATION
Environmental requirements
The Model 9682905 Grinder / Sharpener machine should be
operated in temperatures of 41˚ to 95˚F and humidity range of
25% to 80%.
Power source
The motor is designed for operation on the voltage and frequency
specified. Normal loads will be handled safely on voltages not
more than 10% above or below specified voltage.
