Palmgren 9681109, Руководство по эксплуатации и список запасных частей

Страница: 4 / 24

4
Palmgren Operating Manual & Parts List 9681109 & 9681108
ASSEMBLY (CONTINUED)
ATTACH BELT TABLE
Refer to Figure 2.
Required parts and hardware: Belt table with trunnion, handle, and
8mm flat washer.
1. Position belt table on the belt housing so that the trunnion
travels on the slide.
2. Set the belt table position so that the 0° mark on the trunnion is
aligned with the pointer.
3. Secure belt table position using the handle and flat washer.
Tighten handle into the threaded hole on the belt housing.
Sander is shipped with the belt tension handle at the released posi-
tion. Pull down the handle toward the belt table to tension the belt.
•
Make sure that the clearance between the belt and belt table
does not exceed 1/16”.
•
Wear protective glove and manually push the belt to verify that
belt travels smoothly and without interference.
POSITION DISC TABLE
Required part: Handle
1. Sander is shipped with the disc table attached to the disc guard
using a handle with flat washer one side and a hex head bolt
with flat washer on the other side.
2. Loosen and remove hex head bolt and flat washer from the disc
table.
3. Replace hex head bolt with the handle provided. Secure disc
table to disc guard using the handle and flat washer.
ATTACH ABRASIVE DISC TO CAST IRON DISC
Refer to Figures 3 and 4.
Sander is shipped with the abrasive not applied to the cast iron disc.
1. Clean the cast iron disc if necessary prior to applying the abrasive.
2. Remove the adhesive cover from the back of the abrasive disc.
3. Slide the abrasive between the disc table and cast iron disc and
center abrasive on the cast iron disc.
4. Apply pressure on abrasive to paste.
5. Make sure abrasive is pasted evenly on the cast iron disc.
6. Make sure that the clearance between disc table and abrasive
disc does not exceed 1/16”.
7. Use a straight edge or square to check if the disc table is at right
angle to the disc.
8. Wear a protective glove and manually turn the disc to verify
that the disc turns freely and without interference.
ATTACH MITER GAUGE
Required part: Miter gauge assembly
Miter gauge is shipped completely assembled and can be used
with the belt or disc tables.
• Slide miter gauge bar into the slot on belt or disc table.
INSTALLATION
Refer to Figures 5, 6 and 7.
WARNING:
All electrical connections must be performed by a
qualified electrician.
POWER SOURCE
The motor is designed for operation on the voltage and frequency
specified. Normal loads will be handled safely on voltages not more
than 10% above or below the specified voltage.
Running the unit on voltages which are not within the range may
cause overheating and motor burnout. Heavy loads require that
voltage at motor terminals be no less than the voltage specified on
nameplate. Power supply to the motor is controlled by a single pole
locking rocker switch. Remove the key to prevent
unauthorized use.
GROUNDING INSTRUCTIONS
WARNING:
Improper connection of equipment grounding con-
ductor can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electrical shock.
•
Check with a qualified electrician if grounding instructions are
not understood or if in doubt as to whether the tool is properly
grounded.
•
This tool is equipped with an approved 3-conductor cord rated
at 300V and a 3-prong grounding type plug (See Figure 5) for
your protection against shock hazards.
•
Grounding plug should be plugged directly into a properly in-
stalled and grounded 3-prong grounding-type receptacle, as
shown (Figure 5).
Figure 2 – Attach belt table.
Belt Tension Handle
Table Lock Handle
Figure 3 – Attach abrasive disc.
Figure 4 - Check disc table.
Figure 5 – 3-Prong Receptacle
Properly Grounded Outlet
Grounding Prong
3-Prong Plug