3
SAFETY RULES (CONTINUED)
•
Avoid accidental start-up. Make sure that the switch is in the off
position before plugging in.
•
Do not force tool. It will work most efficiently at the rate for
which it was designed.
•
Keep hands away from moving parts and grinding surfaces.
•
Never leave a tool running unattended. Turn the power off and
do not leave tool until it comes to a complete stop.
•
Do not overreach. Keep proper footing and balance.
•
Never stand on tool. Serious injury could occur if tool is tipped
over.
•
Know your tool. Learn the tool’s operation, application and spe-
cific limitations.
•
Use recommended accessories. Understand and obey all safety
instructions supplied with accessories. The use of improper
accessories may cause risk of injury to persons.
•
Do not over tighten wheel nut. Replace cracked wheel immedi-
ately. Use only flanges supplied with the grinder.
•
Adjust distance between wheel and tool rest to maintain
1
/
16
” or
less gap.
•
Handle the workpiece correctly. Whenever possible, use tool
rest to support workpiece during grinding operation. Turn tool
off if it jams.
•
Always use guards and eyeshields.
•
Clean grinding dust from beneath tool frequently.
ASSEMBLY
ASSEMBLY – 82061B
Parts to be fastened to the unit should be located and accounted
for (See List and Figure 1).
IMPORTANT:
Do not attempt assembly if parts are missing. Use
this manual to order replacement parts.
A
5
/
16
-18 x 1
1
/
2
” Carriage bolt, 4 each
B Spacer, 2 each
C Tool rest bracket, 4 each
D *
5
/
16
” Flat washer, 4 each
E *
5
/
16
”-18 Hex nut, 2 each
F Tool rest, 2 each
G
5
/
16
” Flat washer, 4 each
H
5
/
16
”-18 Hex nut, 4 each
I
*
5
/
16
-18 x 1¼” Carriage bolt, 4 each
J
Upright, 2 each
K Eyeshield, 2 each
L Lower eyeshield bracket, 2 each
M Upper eyeshield bracket, 2 each (left and right)
N #10-24 x
3
/
8
” Pan head screw, 4 each
O *
5
/
16
”-18 Wing nut, 2 each
P Spark guard, 2 each (not shown)
NOTE:
Parts marked with an asterisk (*) are mounted to the
grinder at the factory.
TOOL REST ASSEMBLY
•
Slide
5
/
16
-18 x 1
1
/
2
” carriage bolt (A) into square hole in tool rest
bracket (C). Slide spacer (B) onto carriage bolt. Slide carriage
bolt with spacer and bracket into hole on inside of tool rest (F)
as shown in Figure 1. Slide
5
/
16
” flat washer (G) and
5
/
16
”-18 hex
nut (H) onto carriage bolt. Tighten nut finger tight.
•
Remove
5
/
16
” hex nut (O) and flat washer (D) from
5
/
16
-18 x 1¼”
carriage bolt (I) mounted to bottom front of left wheel guard.
•
Slide slot in tool rest bracket over
5
/
16
” bolt. Replace flat washer
and hex nut. Position tool rest so that distance between tool
rest and grinding wheel is less than
1
/
16
”. Secure all nuts and
bolts.
•
Mount right tool rest in a similar manner.
EYESHIELD ASSEMBLY
•
Remove
5
/
16
” wing nut (E) and
5
/
16
” flat washer (D) from
5
/
16
-18 x
1¼” carriage bolt (I) mounted to top front of left wheel guard.
•
Slide slot in upright (J) over carriage bolt and replace washer
and wing nut.
•
Remove pan head screws (N) from eyeshield assembly. Mount
left upper eyeshield bracket (M) to eyeshield using pan head
screws and lower eyeshield bracket.
NOTE:
Left upper eyeshield bracket is stamped “L” for identification.
•
Slide
5
/
16
-18 x 1
1
/
2
” carriage bolt (A) into square in upper bracket
from right side. Slide upper eyeshield bracket over carriage bolt
and secure with
5
/
16
” flat washer (G) and hex nut (H). Locate
eyeshield in desired position for protecting operator and
secure all nuts and bolts.
•
Mount right eyeshield assembly in a similar manner.
SPARK GUARDS
•
Spark guards (O) are mounted to the grinder using pan head
screws already mounted to wheel guard cover.
•
Remove pan head screws at top of wheel guard covers toward
front of grinder. Secure spark guards to wheel guard covers
using pan head screws. Position spark guard so there is a gap of
no more than
1
/
16
” between grinding wheel and the spark guard.
Tighten pan head screws securely.
Figure 1 – Left Tool Rest and Eyeshield Assembly (82061B)
J
G
G
M
D
C
C
B
D
O
E
F
A
A
L
I
K
H
H
Palmgren Operating Manual & Parts List
82061B, 82062B, 82071B, 82081B & 82101A
