background image

 

Page  16     Gecko Star 2.0                                                                                                                                                                                                                                 01/2017 

 

8  

Replacing the sanding attachment 

 
 
Note! 
The GECKO STAR 2.0 (R) can be reconfigured by replacing the long sanding attachment with the short sanding 
attachment.  
 
 
Caution! 
Unintentional activation of the machine may present a danger.  The machine must be switched off and the main 
cord unplugged for all work on the machine.  
 
Steps: 
 

1.  Switch the machine off  
2.  Unplug the cord from the main power supply  
3.  Unscrew screws (1 = TX30) completely  
4.  Remove the sanding attachment (3)  
5.  Fit the new sanding attachment and drive belt to the machine  
6.  Loosely tighten screws, do not over tighten the screws  
7.  Turn the knurled nut (4) until the drive belt is tight, then tighten screws  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
9.  

Maintenance and care 

 
 

The GECKO STAR 2.0 is largely maintenance-free. The lubrication of the roller bearings and 
of the gears is sufficient for the lifetime of the tool. 
 
We recommend regularly blowing out the air inlets and outlets with compressed air while the tool is switched off.  Failure to 
peform these maintenance checks could result in loss of dust containment.  

 
 
Caution! 
Poor maintenance can cause the motor to overload more rapidly, and lead 
to increased vibration and noise emissions. 
 
 

 
 
 
 
 
 
 

Содержание GECKO STAR 2.0




















Отзывы: