Pallas Condor, Руководство по эксплуатации

Страница: 15 / 76

Manual Pallas Condor 15
ENG
LI
SH
6.2.3 Feed water hardness - H
Note: Determine the feed water
hardness in °tH. 1 D° = 1,78 F° = 17,8 ppm
• Adjust the
water hardness
with and
• Press to
validate the selection and advance
to the next parameter.
6.3. START A MANUAL REGENERATION
There are 2 options to initiate a
manual regeneration:
• Press and release the button.
The tap icon will start flashing, to
cancel the regeneration request
press button, the icon will stop
flashing.
The regeneration will start at the
set hour
• Press and maintain for 5 seconds
the button, the regeneration will
start immediately
To advance to the nex regeneration
cycle, press the button.
This will have no effect if the valve is
already advancing to the next cycle.
User Guide Fleck 9100-SXT
Ref. MKT-UG-008 / C - 14.11.2019 7 / 36
EN
Feed Water Hardness
Note:
Determine the feed water hardness in °tH.
Reserve capacity
Note:
Determine the reserve capacity in Litre or in percentage.
Current day of the week
Note:
Determine the day of regeneration (1 for Monday, 2 for Tuesday, 3 for Wednesday, 4 for Thursday, 5 for Friday,

6 for Saturday and 7 for Sunday).
4.2. Diagnostic mode
To access the recorded informations, press and simultaneously for 5 seconds. Press to see the next data. Press
to exit the diagnostic mode.
5 . Operation
5.1. Recommendations
• Use only regenerate salts designed for water softening EN973;
• for optimal system operation, the use of clean salt free from impurities is recommended (for example salt pellets);
• do not use ice melt, block, or rock salts;
• the sanitizing process (both with liquid and electrochlorination) introduces chlorine elements which may reduce the lifetime
of the ion exchange resins. Refer to the technical guides for resins in common use, providing necessary checks on the
system.
5.2. Manual immediate regeneration
A
Press and hold for 5 seconds.
6 . Error codes
The following error codes may be displayed during operation:
7 . Maintenance
Mandatory:
Cleaning and maintenance shall take place at regular intervals in order to guarantee the proper
functioning of the complete system, and be documented in the Maintenance record book.
Mandatory:
The maintenance and service operation must be done by qualified personnel only. Failure in respecting this
may void the warranty.
8 . Troubleshooting
Please follow this procedure for any technical support:
A
Collect the required information for a technical assistance request.
→
Product identification (see 2.1. Serial label location, page 5 and Original settings, page 2).
B
Contact your local dealer who installed this device (see contact details on last page).
F
Adjust the water hardness with and .
G
Press to validate the selection and advance to the next parameter.
H
I
Adjust the reserve capacity with and .
J
Press to validate the selection.
K
Adjust the day of the week with and .
L
Press to validate the selection.
---0 Cam sense error: Unplug the unit and plug it back. If error continue, call technical support.
---1 Cycle sense error: Unplug the unit and plug it back. If error continue, call technical support.
---2 Regen failure: Perform a manual regeneration. If error continue, call technical support.
---3 Memory error: Call technical support.
7. COMMISSIONING
We recommend the following steps
for the commissioning of the softener.
Wait to put salt in the softener till the
end of the commissioning in line with
the guidelines below.
• Put the softener on a smooth and
horizontal surface.
• The plumbing must be done
according to the rules of the
profession. The diameter of the
drain should be larger than the
rinse outlet of the valve.
• Close the bypass, a water tap and
the inlet valve and let the water flow
for some time to remove the air and
the present particles (due to the
plumbing).
• Plug the SXT controller to the
power source
• Proceed to programming according
to chapter 6 ‘Programming of the
Pallas Condor’.