palintest Micro 800 Скачать руководство пользователя страница 36

Страница: 36 / 41

Micro 800 Optical DO Instruction Manual

Rev 1

www.palintest.com

Page 36 of 41

Troubleshooting Continued …

Problem

Cause / Remedy

Dissolved Oxygen
readings are inaccurate
or unstable.

The DO sensor may need calibrating. Recalibrate.

The DO sensor cap may be fouled. Clean the DO Cap.

The DO Cap may be damaged. Inspect and replace if

necessary.

Calibration may have been carried out at an extreme

temperature. Recalibrate at a temperature as close to the
sample temperature as possible.

EC readings are
inaccurate or unstable.
Error 09 shows during
calibration of EC.

Have you got the Probe Sleeve fitted? EC will not work without

the Probe Sleeve fitted. The only exception to this rule is if the
Probe is being used with a Flowcell.

The Probe may not be inserted deep enough into the sample

being measured. Ensure the sample level reaches the top set
of holes on the Probe sleeve.

Trapped air bubbles may be causing problems. Tap and swish

the Probe to dislodge them.

The Probe Sleeve may be loose. The Probe Sleeve must be

absolutely rigid with respect to the Probe Body for correct EC
operation.

The EC electrode may need recalibrating. Recalibrate.

The EC electrode may be dirty. Clean the EC electrode then

recalibrate.

17.

DECLARATION OF CONFORMITY

Palintest Ltd declares that the equipment described herein is in compliance with the
essential requirements and other relevant provisions of Directives

2004/108/EC and

1999/5/EC.

Содержание Micro 800










































Результаты поиска

Содержание Micro 800

Отзывы:

Бренды по названию

Популярные бренды

palintest Micro 800, Инструкция по эксплуатации

Результаты поиска

Содержание Micro 800

Отзывы:

Бренды по названию

Популярные бренды